What did you do to your GT350 today?

[sox3]

A little bling accent for the engine bay. I'm trying to give it a little color as it tends to be so bland.
Bemaro Films has some great Vinyl products and this Carbon Fiber Letter overlay was my first choice. The install was a struggle at first because I did not have the ambient temperature in the garage at a high enough level. I was able to get out my heat gun and some 3m adhesive promoter to finish the job. Turned out ok.
I may wait until summer to install the rest of the vinyl I purchased from them.
.

Lorne,
Care to share what other vinyl you have to install?

Sponsored

 

[Lorne34]

Lorne,
Care to share what other vinyl you have to install?

Here is the full lineup for the GT350 from Bemaro Films in the link below
I purchased:
composite fiber overlay for radiator support
Badge overlay for front grill and rear decklid
side mirror accents
steering wheel stripe (Red)
Brembo Caliper overlays

https://www.bemarofilms.com/onlinestore?VEHICLE=2016-2020+Shelby+GT350/R

 

[TeamGomez]

Jumping into the coating world and nabbed some CarPro DLux for the wheels and calipers. Pulled ‘em, scrubbed ‘em, clayed ‘em, IPA’d ‘em, then (finally) sealed the deal. Fronts, barrels, and calipers. Did a single coat and it took approx 6ml of the 30ml bottle. We’ll see how it holds up. Pix and a PSA…

 

[Mjc1241]

Both passenger side strut and shock were leaking, so I had Speed Foundry in Roswell, GA install these including an alignment:
https://www.steeda.com/ford-genuine-40-1016-103-mustang-magneride-kit

 

[Ahung12]

Got the tach over 8k rpms yesterday for the first time. To hear the exhaust in videos is one thing, but to hear and feel it inside the car is quite another. Wowowow.

 

[mavisky]

Took the new wing to lunch.

 

[Inthehighdesert]

Curious to see if you notice a difference from oem.

Both passenger side strut and shock were leaking, so I had Speed Foundry in Roswell, GA install these including an alignment:
https://www.steeda.com/ford-genuine-40-1016-103-mustang-magneride-kit

 

[Mjc1241]

It may be a placebo effect but it feels stiffer in Sport mode. The original struts/shocks were going on eight years old so it may just be having new parts on. I was told that the damping is different when I called Steeda prior to purchase and they are an upgrade over the standard GT350 OEM set-up.

Curious to see if you notice a difference from oem.

 

[CobaltFilly]

Installed a Ford Performance M-5200-MSS exhaust system today. So far it sounds pretty good but will have to wait until spring to fully enjoy the new sound. What do people do with the old exhaust system? Cut it apart and sell them? It does have a Lethal Performance resonator delete pipe that is in great condition.

Donate it to a base model near you...

(Save it, as Lorne suggested.)

 

[wingnutt]

finally ordered a replacement splitter…
…tired of zip ties and flex tape to keep it together

Both passenger side strut and shock were leaking, so I had Speed Foundry in Roswell, GA install these including an alignment:
https://www.steeda.com/ford-genuine-40-1016-103-mustang-magneride-kit

…bookmarked for future use

 

[TeamGomez]

Both passenger side strut and shock were leaking, so I had Speed Foundry in Roswell, GA install these including an alignment:
https://www.steeda.com/ford-genuine-40-1016-103-mustang-magneride-kit

Curious how many miles before the struts started leaking.

 

[wingnutt]

Curious how many miles before the struts started leaking.

I think it’s luck and/or consistent use…I’m about to clock 60k on my 350R and not a drip or drop anywhere

 

[tangermean]

Installed a Ford Performance M-5200-MSS exhaust system today. So far it sounds pretty good but will have to wait until spring to fully enjoy the new sound. What do people do with the old exhaust system? Cut it apart and sell them? It does have a Lethal Performance resonator delete pipe that is in great condition.

I wish you were closer! I am looking for the factory axle back, the hangers on mine at the bend just before the mufflers broke.

 

[ChipG]

I wish you were closer! I am looking for the factory axle back, the hangers on mine at the bend just before the mufflers broke.

Couldn't you just get the hanger welded up? One of mine has broken and I'm just going to weld it back together.

 

[tangermean]

Couldn't you just get the hanger welded up? One of mine has broken and I'm just going to weld it back together.

I am going to try. The hanger pipes are hollow and thin so its going to be more difficult than if they were solid.

Sponsored