What did you do to your S550 Mustang today?!

[GTP]

Great news I used my wife's smart phone, and I have much better pics. Now the problem is how to put them on my laptop. I don't think the string is long enough to reach.

Don't use the string method. Use Bluetooth method. Better yet, just post from her phone, no transfer needed!

Sponsored

 

[Craig Brown]

Ok, this is with my wife's phone, and I just don't know if they are any better. It also shows the purge valve mount I made. And the 2015 engine cover I modified to fit on a 2018 manifold. I hope this meets the high standards of this group.

 

[LCK22GT]

First nice day in few, so why not?

 

[Bob Lob Law]

Made a few pulls against a C8 with a NX 75 shot. They hook really well and both times I spun a little then walked away from him. Pulled over and chatted a bit. He's also got a C7 both in yellow. Good times!

 

[Craig Brown]

Made an adaptor to fit into the purge valve e-vap line to finish the smoke test, and I made a wedge spacer so that my UPR catch can would no longer touch the back of my UPR expansion tank. I took the 5.0 badge off the 2015 engine cover and remounted it on the radiator cover by the hood latch.

 

[Rilot]

Eibach Pro-Kit springs went on, as did the Steeda IRS lockout.

I'm very happy with how it sits now. Oddly, it seems to be less fidgety over bumps and has less scuttle shake. I expect a fair amount of that is because of the IRS lockout rather than the springs though.

 

[tomservo92]

Washed it (before the Texas heat set in).

 

[compprep]

Went to dealer for backup camera recall. They deemed not required... So out for a drive.

 

[Headless Horseman]

Went to dealer for backup camera recall. They deemed not required... So out for a drive.

They sent me that recall. I never went in for it. Now they say it's unnecessary?

 

[Snakebyte]

They sent me that recall. I never went in for it. Now they say it's unnecessary?

Not every Mustang has the issue. The recall checks to see if your camera falls into the potential fail mode.

 

[LCK22GT]

They sent me that recall. I never went in for it. Now they say it's unnecessary?

Same here. I’m not taking it in unless it acts up.

 

[NGOT8R]

I installed my BL Fabrications steering wheel brackets and buttons for the clutch slipper and turbo scramble.

 

[High Velocity]

I finished installing Anderson Composites front lip, front grille, front corner pockets, side skirts and rear diffuser on my buddy's car. He added those funny looking lights to the grille, I told him I don't like them but hey it's his car. I believe he went to the store and found closet lights and glued them in to this expensive grille lol

 

[MAGS1]

I finished installing Anderson Composites front lip, front grille, front corner pockets, side skirts and rear diffuser on my buddy's car. He added those funny looking lights to the grille, I told him I don't like them but hey it's his car. I believe he went to the store and found closet lights and glued them in to this expensive grille lol

A guy here on the forum makes these housings for the Diode Dynamics SS3 lights for the Mach grille. Tell your buddy to do it right

https://ace-engineering-2.myshopify.com/

 

[G.T.]

Replacing all the important relays in the fuse box (which is pretty much all of them lol).

Done with all the big 4-pin ones, waiting on the 5-pin for the radiator fan (FC2) to come in.

The new relays are slightly bigger and heavier than the old ones. I hope it translates to reliability!

Sponsored