What did you do to your S550 Mustang today?!

[ice445]

Added Carbon Ceramic front rotors to my GT350R - OEM from a 2019 Ford GT

Most expensive flex I've seen on here in a long time, lol. Bet it puts your face through the windshield now. Looks great.

Got my trans and diff fluids from Summit. I decided to stick to the factory weights/oil types, I just went with some quality aftermarket synth fluids that are equivalents. Now I just have to not be lazy and install it. I'm going to make my own fluid transfer pump to avoid pumping hundreds of times with those crappy hand pumps.

Sponsored

 

[HoosierDaddy]

Put a 2018 EcoBoost Pony Package decklid trim panel on my coupe.

Nice!

Would love one. But I checked prices when those were new and they were mega expensive and since the 2018+ panels are even easier to scratch figured a pristine junk yard panel wasn't going to happen.

If you found a source for reasonably priced new, please PM me.

 

[lacanteen]

With this going on across the street, it's been impossible to keep my car clean. To add to the dirt, 100 yards beyond these piles a pond was dug and the dirt spread around.

 

[GTP]

$1-200 for a car cover?

 

[GTP]

Finally got around to changing the oil. Was more than 1000 miles late, but I didn't want to mess with it in the cold.

Picked up the PUP oil deal with rebate from Walmart.

Change was the fastest and cleanest yet. I use the Ronin drain plug. The flex spout you see fit my Amsoil jugs but not the Pennzoil so I had to use a funnel this time.

The foil is to wrap over the harness, and the cutout 44oz drink cup goes around the FL820s filter. It is my hack for having the filter oil drain past the frame.

 

[2morrow]

This weeks project.. Not on the Mustang but For the Mustang..
Box, bench, cabinets, countertop, winch, tie downs, backup camera and Curt weight distribution hitch installed… Ready for VIR on Friday.. NASA time..!!,

Coin Rubber flooring, paint and exterior graphics to go in/on over the next weeks..

Everyone loves a project..!

SIIIIIIIICCCCCCCKKKKKK!!!!!!!!! Make sure to post some pix when it's all done.

Added Carbon Ceramic front rotors to my GT350R - OEM from a 2019 Ford GT

Double SIIIIIIIICCCCCCCKKKKKK!!!!!!!!! lol

 

[JnBama]

With this going on across the street, it's been impossible to keep my car clean. To add to the dirt, 100 yards beyond these piles a pond was dug and the dirt spread around.

Same here construction all over the area it is either dust or mud and rocks all over the roads from dump trucks

 

[2morrow]

Bought some new parts!

Exedy Mach 500 Clutch Kit
Exedy Lightweight Racing Flywheel
McLeod SS Clutch Line
McLeod Pressure Plate Bolts
FP Flywheel Bolt Kit

 

[MotoMike]

I let mine sit in the garage since it was wet here today!

 

[Jazzman0718]

I did my first oil change using jacks- and this is my first change on this car. I took the battery tender off and drove her around the block a few times to get her hot afterwords. She's been hibernating since November. It was a GREAT afternoon.

 

[BigR4444]

Replaced my scratched up decklid panel; and instead of another "GT" badge, I added my own custom decklid emblem.
(Car's name is Absinthe)

 

[Crayon]

Replaced my scratched up decklid panel; and instead of another "GT" badge, I added my own custom decklid emblem.
(Car's name is Absinthe)

Nice! That's my plan too sometime this year. I want to get the plain one to put my own badge back there.

 

[BigR4444]

Yoast Fabrication did it for me.
Yofab.com

FYI for you or for anyone else; this fell under the "custom full color fusion emblem"
They offer a lot of other different options though.. you could probably come up with something very unique and creative.

I originally went with acrylic, but when I tried to press it down, the decklid's slightly curved surface caused the emblem to crack; as that acrylic had no give.
We tried again with aluminum composite. Which proved to be much more flexible; and the outcome was really good.

They actually felt bad for me and gave me a break on the price the second try, plus they made it super quick. I'd highly recommend them.

 

[Cobra Jet]

Added Carbon Ceramic front rotors to my GT350R - OEM from a 2019 Ford GT

So what’s the cost of replacement when that time comes around for both the rotors and pads?

Any advice you can give for the install - was it direct swap, or were modifications and additional hardware needed to make it all work?

 

[Brian_S550]

Nice!

Would love one. But I checked prices when those were new and they were mega expensive and since the 2018+ panels are even easier to scratch figured a pristine junk yard panel wasn't going to happen.

If you found a source for reasonably priced new, please PM me.

I bit the bullet to get exactly what I wanted, and ordered a new one from Tasca.

Sponsored