What did you do to your S550 Mustang today?!

[Dr. Norts]

came home wife had pulled Mustang out of garage so she could paint some crafts. I had it cleaned just sitting in garage now sitting out in rain
her answer was you can clean it again

Savage!

Sponsored

 

[WD Pro]

Took it for a drive.

Found out it either can’t read, it’s colour blind or it’s got a rebellious side - which ever it is, I thought it deserved a picture :

WD

 

[WildHorse]

Finally got those licence plate holes fixed. I specifically told them not to drill the holes when they did the PDI, not naturally they did the opposite haha.

 

[Reddirocket27]

Finally got those licence plate holes fixed. I specifically told them not to drill the holes when they did the PDI, not naturally they did the opposite haha.

They sell color matched plugs, they're like $4 lol

 

[WildHorse]

They sell color matched plugs, they're like $4 lol

Had em. Didn't like them. So the end result was getting it professionally fixed. After, they're gonna paint correction & ceramic coat the whole shebang. Then, it's getting put away for the winter.

 

[m3incorp]

The parking police would have to get a laugh out of that one. I would probably park there also.

 

[WD Pro]

@Mikthehun1 - I did look for a green zone, but only had a choice of red and blue, blue won as it was much quieter and had more empty spaces ... lol

WD :lol:

 

[bknight21]

I installed the paddle shifter extensions that I have been seeing more and more people on here getting. For only $20 they will do the trick.

 

[FreePenguin]

I found wheels I really like.... I found a grabber blue with the same brushed titanium finish for color reference. but different rohana wheels here are some photos of my car before/after.

What do you guys think? I would get the same size so they fit where I am at now, not tucked in like the mustang s550 that has it. They are Rf2 rohana brushed titanium-- also do you think my chrome window trim might clash with the brushed titanium wheels?

My wheels arrive Friday, and my 5mm spacers. The wheels are offered 20mm and 40mm offset. Since I own 20mm spacers I decided 40mm I can always space to 20mm but I’m gonna try the 40mm with 5mm HUbcentric spacers first

My tires are 255/40/19

Wheels currently are
19x9.0 45 offset with 20mm spacers all around (25mm offset with spacers)

new wheels
19x9.5 40mm offset, but I have both 5mm and 20mm spacers at my disposal. Gonna toss 5mm squared first to see stance. I imagine that’s what I will use. Nice flush in rear.

would 20mm make them flush in front? (19x9.5 20mm) if I used 20mm or should I use 5mm in front too.

 

[Solteka]

I received a tune revision from PD Tuning for my car today so I uploaded it right away, going to start the datalogging at the right time:

 

[WildHorse]

Finally got those licence plate holes fixed. I specifically told them not to drill the holes when they did the PDI, not naturally they did the opposite haha.

All paint correction done, and ceramic coated. Tell me again just go buy some 4$ plugs haha

 

[FreePenguin]

All paint correction done, and ceramic coated. Tell me again just go buy some 4$ plugs haha

Looks great, GB unite.

ohio got rid front plates this year, very happy with that, your car looks great.

 

[WildHorse]

Looks great, GB unite.

ohio got rid front plates this year, very happy with that, your car looks great.

Thanks, here the law states
" Manitoba law requires that a licence plate be affixed to both the front and rear of the vehicle. (Exceptions are repairers, dealers, motorcycles, mopeds, tractors and trailers. These types of vehicles have one plate, which must be affixed to the rear of the vehicle.) "
Makes no mention of where on the front or rear of the car you can mount the plate. Almost 4 years now, never got hassled for the front tucked inside the lower grill.

 

[FreePenguin]

I did that before the law went in effect, I put a rectangle of PPF on the front bumper, then put double sided 3m sticky tape all around the edge of license plate back. then I stuck it to the PPF, I removed the PPF and the license plate came off with it lol

 

[Chef jpd]

Was disgusted by the engine cover atrocity on my 2020.

So, ordered the Bullitt "fuel rail covers", then did a big trim of the factory cover only retaining the center section.

Also did a sound tube delete while I was there.

Thoughts?

20201021_144836 by chefjpd, on Flickr

20201021_153408 by chefjpd, on Flickr

20201021_153423 by chefjpd, on Flickr

And, while I was there, I plasti dipped the tops of the headlights. No reason to light up under the hood.

20201021_153432 by chefjpd, on Flickr

Sponsored