No remote start on manual 2019?

[TexasRebel]

Is the remote start missing entirely from the software in MT cars, or is it merely hidden/deactivated? In the latter case, couldn't it be activated somehow with FORScan?

Missing entirely. The remotes for MT and AT cars operate on completely different frequencies. To enable remote start you'd have to change out the hardware to match an AT and without the transmission present would open a whole can of DTCs for missing sensors.

Also, unless they completely reworked the case for 2019 the MT has no gear position sensors except reverse (for lights & camera). The gear indicator works off of a speed/engine/final drive algorithm.

Sponsored

 

[Vlad Soare]

Well, that settles it then. Thanks.

 

[Echo4papa]

All of the safety features that people are blasting have a significant impact in reducing high value insurance claims. As cars become safer overall and claim totals decrease, so do insurance rates. I was sitting in an excruciatingly boring work related conference one day, insurance related, and this very topic was being discussed and how it's already started to impact claim data. The presenter said he expected to see a drastic reduction in rates over the next 10 years as newer cars become increasingly more safe and more older cars are removed from the roads. Personally, I think it will be longer than 10 years because most of our population doesn't get a new car every 5 years... or doesn't even buy new to begin with, so it might take a lot longer to cycle through older vehicles in usage.

 

[boB]

Missing entirely. The remotes for MT and AT cars operate on completely different frequencies. To enable remote start you'd have to change out the hardware to match an AT and without the transmission present would open a whole can of DTCs for missing sensors.

Also, unless they completely reworked the case for 2019 the MT has no gear position sensors except reverse (for lights & camera). The gear indicator works off of a speed/engine/final drive algorithm.

The 2019 service manual shows a gear selector component with a 6 pin connector in the electrical section. It appears to be located on top of the transmission, I hope to get a photo of it next time I am under my car.

 

[MegaMagneticStang]

do ford dealerships accept returns? if so, someone can purchase that remote start module and give it a try. install it, see if the auto start options come on the menu somewhere. if so, thats a good first step, after that, its just a matter of working out a temporary switch for the clutch.

if you dont see any new programming, return it to the dealer right?

 

[shogun32]

its just a matter of working out a temporary switch for the clutch.

it's way more than some switch. If the clutch is not depressed (thus releasing the interlock) the engine will not crank. You can defeat the interlock but it would be incredibly stupid to not also ascertain the transmission is in neutral.

There is some kind of sensor in the 19+ trans because that's how auto-blip knows what gear selection you're in the process of making and blips the throttle to match speed. The absence of "gear selection" signal, however may not mean you're really in Neutral. Is it really so damn hard to go start the car and sit there? Or if you must, go back in the house and let it warm up?

 

[TexasRebel]

it's way more than some switch. If the clutch is not depressed (thus releasing the interlock) the engine will not crank. You can defeat the interlock but it would be incredibly stupid to not also ascertain the transmission is in neutral.

There is some kind of sensor in the 19+ trans because that's how auto-blip knows what gear selection you're in the process of making and blips the throttle to match speed. The absence of "gear selection" signal, however may not mean you're really in Neutral. Is it really so damn hard to go start the car and sit there? Or if you must, go back in the house and let it warm up?

If the rev-matching is actually trying to match and not just blindly bumping the RPM up, the easy (read: cheaper with fewer parts/programming/failures) way is to measure the input shaft RPM and have the engine match that. In fact, you can ascertain which forward gear the transmission is in by simply comparing tachometers on the input and output shafts. Ground speed and final drive are irrelevant. (that may be the 6 pins... 2 for Reverse, 2 for input RPM, 2 for output RPM)

"automatic" rev-matching is a bit pointless to begin with as all it will do is save some wear on the clutch. Unless you're double-clutching, the engine cannot manipulate the input side of the transmission to assist in getting into gear... that's still on the synchros.

 

[shogun32]

If the rev-matching is actually trying to match and not just blindly bumping the RPM up

I haven't spent a lot of time exhaustively instrumenting anything but if I shift out of 4th, and 'touch' 3rd gear gate but not actually engage it, the engine revs to whatever the speed it would be at had I finished the motion. If I then go over to 2nd and 'touch' the gate it'll rev much higher in anticipation of engagement. The syncros still have to do their thing. It's not a simple-minded "just add 500 rpm" kind of logic.

The auto-blip is intended to minimize the "drag engine up to speed" scenario when the clutch is let out.

 

[TexasRebel]

I haven't spent a lot of time exhaustively instrumenting anything but if I shift out of 4th, and 'touch' 3rd gear gate but not actually engage it, the engine revs to whatever the speed it would be at had I finished the motion. If I then go over to 2nd and 'touch' the gate it'll rev much higher in anticipation of engagement. The syncros still have to do their thing. It's not a simple-minded "just add 500 rpm" kind of logic.

"Touching the gate" should be enough to put pressure on the synchros and spin up the input shaft.

 

[boB]

Here is what the 2019 service manual shows: so we have the usual power and ground, three gear sensor wires, and the mysterious RS.

 

[MaskedRacerX]

Here is what the 2019 service manual shows: so we have the usual power and ground, three gear sensor wires, and the mysterious RS.

RS ... ? ZOMG!@!@! RS = REMOTE START !!!!

 

[shogun32]

3 bits express 0-7 gears. which value is 'reverse' I don't know. RS could be reverse too.

 

[TexasRebel]

Here is what the 2019 service manual shows: so we have the usual power and ground, three gear sensor wires, and the mysterious RS.

VRef = Reference Voltage (5 or 12)
Gear Sensor Position 1 = input shaft speed
Gear Sensor Position 2 = output shaft speed
RS = Reverse Sensor
TRGND = Ground

BDCPM could be a neutral sensor. The only acronym I can find is Brushless DC Permanent Magnet. Knowing the gear selector is between gates would prevent the computer from displaying anything except N.

There's also that C1046 connector in both RS and Gnd.

Sponsored