New PB in the 2020

[TKM Conbread]

Went out friday and made 2 hits and was able to get a new PB…. Was able to run a 5.91 at 122 …. Second pass went a faster .60 but shook the tires around 150 foot!!! Full Weight PP1 car..
Procharger D1x 18 psi
Built A10
Circle D converter
Fore tripple pump
Id1300
Stock motor
Still footbrake the car…
Over all had a great time, i think the car will go in the 5.80 range and i drive it all over the place…

Sponsored

 

[TKM Conbread]

Not sure if the Bell done anything to the blower, but the car seemed very aggressive than it did before… Also last time i ran it was in the 98 degree range… this night it was 75 degrees..

 

[SolarFlare]

good outing, congrats

 

[TKM Conbread]

Thank you

 

[andrewtac]

Thank you

Nice, trying to get back to run mine before they shutdown Baytown. What RPM do you launch at off the brake? Hope to be about what your running, I have a very similar built; except vortech.

 

[TKM Conbread]

Nice, trying to get back to run mine before they shutdown Baytown. What RPM do you launch at off the brake? Hope to be about what your running, I have a very similar built; except vortech.

I left off idle, and just drove into the converter for it to flash real hard….. i wish i had more time to play with diff stall speeds, but we was having a Race with our other cars… pretty sure the converter flashes 38-4000 rpm

 

[andrewtac]

I left off idle, and just drove into the converter for it to flash real hard….. i wish i had more time to play with diff stall speeds, but we was having a Race with our other cars… pretty sure the converter flashes 38-4000 rpm

Thanks, mine flashes about the same. I'll give that a try.

 

[cobra199711]

Wow, that freaking car scoots and sweet looking!

 

[I Bleed Ford Blue]

Do you have better axles and a stronger driveshaft to handle all that power? I see you already have a built A10 and sticky tires, just add a transbrake and that will get you 5.80's for sure. HP tuners has software update to add a transbrake on the A10, no extra hardware, wiring or switches needed, it uses the paddles to activate and use the transbrake.

 

[TKM Conbread]

Do you have better axles and a stronger driveshaft to handle all that power? I see you already have a built A10 and sticky tires, just add a transbrake and that will get you 5.80's for sure. HP tuners has software update to add a transbrake on the A10, no extra hardware, wiring or switches needed, it uses the paddles to activate and use the transbrake.

i have Dss 2000hp axles, and Dss aluminum driveshaft (wish i would have done carbon) PBD sent me the trans brake tune up, but i couldnt never get it to work… need to see if they will try and resend it

 

[I Bleed Ford Blue]

there are videos on YouTube to show you how to use it.

 

[TKM Conbread]

there are videos on YouTube to show you how to use it.

Thanks man, i will give it another shot… i may have been trying it in DragRace mode…

 

[Mach1soldier]

Car is booking! I have the same combo pretty much except no skinnies and 11 psi of boost. Curious to see what the skinnies do since I’m stuck at 6.53 with a 1.56 60 footy

 

[vtknight]

Congratulations - that is a solid run! That is a super solid MPH...A couple of questions; what power are you making? When you say built trans - anything beyond Circle D and clutch packs? (Midnight Performance etc.). Thanks and well done!

 

[TKM Conbread]

Congratulations - that is a solid run! That is a super solid MPH...A couple of questions; what power are you making? When you say built trans - anything beyond Circle D and clutch packs? (Midnight Performance etc.). Thanks and well done!

last time i dynoed the car it made 964 but i could see where it started falling off up top… so now i have a 1320 ported Boss intake on the way to try, they suppose to pull all the way thru 8500rpm..

trans is clutch kit and i done a valve body but dont think i needed to… yes circle D converter 4c 3800-4000

Sponsored