2018 Digital Cluster Installation Guide

[Serp305]

I just did a cluster swap but im getting this errors, any idea where in forscan I can find parameters to disable the front camera and rear belt monitor?

Update: I figure it out, save me $150.

Sponsored

 

[Socal Stangman]

So I have a question. I just picked up a 2015 GT with the digital cluster conversion already done. When I go into the menu to configure the gauges, it gives me the option to choose the oil pressure gauge. When I do though, I doesn’t read anything, does it not work with my car or is it possibly not turned on? If I can turn it on to read pressure, how do I do it with Forscan?

 

[Ferrcad]

So I have a question. I just picked up a 2015 GT with the digital cluster conversion already done. When I go into the menu to configure the gauges, it gives me the option to choose the oil pressure gauge. When I do though, I doesn’t read anything, does it not work with my car or is it possibly not turned on? If I can turn it on to read pressure, how do I do it with Forscan?

Does not work with our cars, no oil sensor to read hence the issue. Normal behavior with this upgrade on a 2015.

 

[Socal Stangman]

Does not work with our cars, no oil sensor to read hence the issue. Normal behavior with this upgrade on a 2015.

Bummer, thanks for the response

 

[andy9111]

I just did a cluster swap but im getting this errors, any idea where in forscan I can find parameters to disable the front camera and rear belt monitor?

Update: I figure it out, save me $150.

how did you fix it? im having the same issue

 

[Atticaz]

trying to hook up a buddies car and practicing to do mine., in the near future.

The spreadsheet says 720-10-01: XXXX - X * XX 4=Enable 0=Disable for Auto Rev matching.
The list only goes up to 720-07-02 on his car, in IPC (as-built)??

Did you mean 720-01-01: XXXX - X * XX 4=Enable 0=Disable for Auto Rev matching or Do the do 720-08-001 through 720-10-002 and up show up after the digital cluster is hooked up?

 

[TnWHTMARE]

I just did this swap on my 301a over the weekend. Talk about easy. Didn't pull the steering wheel, just the airbag to change out the 2 right switches. Left the lower cover attached to the steering column and just popped the upper loose.

I got a ABD file from Breeves, had a little glitch with the flash part which he helped me with and boom.....works like a charm. Super easy to do thanks to Breeves and the other trailblazers here. Thank you all!

 

[lkeltner]

I installed the digital dash about a year ago on my 17GT PP1 and it's amazing. I've fought, however, with rattles since the day I put it in. I've pulled the dash apart 3x trying to fix it, adding foam everywhere, and it always starts rattling again on bumps.

I've gone so far as to start planning to 3d print some supports that can somehow attach the top ears of it to the car somehow, but before I go through all that trouble, is there some better definitive guide to making this thing not rattle?

 

[HoosierDaddy]

I've gone so far as to start planning to 3d print some supports that can somehow attach the top ears of it to the car somehow.

I've been waiting for something like that.

 

[lkeltner]

I've been waiting for something like that.

Sounds like I need to get started then ;)

 

[Ferrcad]

Guys, look here in the thread.. Response #880

https://www.mustang6g.com/forums/th...installation-guide.99275/page-59#post-2468051

I made some of these and when I did my install that was all that was needed. Dimensions and all are right there for you. Stiffened the thing perfectly. Drilled some starter holes, followed up with self taps screws. Extra padding and no issues going on 3 years...

Good luck!!!

 

[HoosierDaddy]

No more rattle! The angle slightly cuts off the very top of the dash display but nothing that warrants any additional tweaking. Worth it to have a solid install. Thanks for the tip

Narcopost. If still around, are you saying part of cluster is blocked due to extra brackets bolt holes being off a little?

 

[Ferrcad]

Narcopost. If still around, are you saying part of cluster is blocked due to extra brackets bolt holes being off a little?

Not sure how he did his but if you take your time they fit perfectly. No cutoff of the top of the speedo.

 

[lkeltner]

Guys, look here in the thread.. Response #880

https://www.mustang6g.com/forums/th...installation-guide.99275/page-59#post-2468051

I made some of these and when I did my install that was all that was needed. Dimensions and all are right there for you. Stiffened the thing perfectly. Drilled some starter holes, followed up with self taps screws. Extra padding and no issues going on 3 years...

Good luck!!!

Thank you!

 

[Ferrcad]

Found these pictures after my install as you can see... no screen cutoff! As I said, take your time and you'll be fine!!!

Sponsored