Search results

Any issues running 1" spacers on the rear only?

I'm preparing to get tuned (93, FF, e85r) I've already purchased and installed a Ngauge and will be tuning with Tuning by James and curious about monitoring ethanol content. I would like to monitor using the Ngauge as opposed to tube testing. I see some are using this kit...

Just received my new ngauge and it doesn't come with any documentation or quick start guide. I'm going to mount it in an A/C vent using a Joleobee magnetic mount. I wont be getting tuned for a while so no tune to load at this point, I just want to get it up and running. I assume there is a...

I have cylinder head temp, IAT, and A/F gauges set up in my digital dash but would rather see lines of text with the actual numbers than gauges, but don't know how to do it. This is what I'm talking about: What's the secret?

I'm beginning to gather info on headers for my Bullitt and it will be a while, but should I be looking at 1-3/4 or 1-7/8 for street use? Also, which header is better fitting (clearance) than others? I see some are very close to the A/C lines.

Out of curiosity, does anyone know if a factory 2018 mustang GT air box and tube work on our Bullitts? I want to go to closed box, probably the steeda, but it uses the bottom half of the stock closed airbox which we don't have.

Anybody using this mount? Looking for feedback and opinions on best way to mount ngauge. Curious if it's necessary to remove dash piece for A/C vent removal to accommodate the gauge. https://www.joleobee.com/wp-content/uploads/2019/10/S550-Magnetic-Vent-Mount.mp4

Been chasing a very annoying clunk/rattle and couldn't tell where it was coming from until today. Recent upgrades were MGW shifter, Borla Xpipe, Differential lock out bushings, Steeda stop the hop kit with subframe bushings. At first I was sure it was something I did during the installs, went...

In the process of installing the BMR differential bushing lock out kit on my 2019 Bullitt I had to remove the part in the attached pics. The passenger side rear dif bolt ran through it, but it had to be removed for the install. No mention of it in the instructions. What it is it? Do I have to...

In the process of installing the BMR differential bushing lock out kit on my 2019 Bullitt I had to remove the part in the attached pics. The passenger side dif bolt ran through it, but it had to be removed for the install. No mention of it in the instructions. What it is it? Do I have to put it...

Not really the time of year for this, but VP released Stay Frosty coolant. Probably no good to you guys north of Florida. https://vpracingfuels.com/product/stay-frosty-racing-coolant/

The Steeda kit has been on order for a couple of weeks now and today I ordered the other parts from BMR. I read a multitude of posts and talked to vendors until my head hurt and finally pulled the trigger. Did I go overboard? 555 4455 Steeda S550 Mustang 'Stop the Hop' CB010 2015 - 2018...

I have a Steeda "stop the hop starter kit" #555-4455 coming for my 2019 Bullitt and looking for recommendations for additional parts. My car is a weekender and will only see hard street driving and occasional 1/4 mile racing. After the aforementioned Steeda unit, what additional mods are...

https://www.diyford.com/ford-coyote-engine-cooling-system-performance-guide/

What is the biggest restriction in the Bullitt exhaust? I would love to do long tubes but looking at the install and the high cost will probably keep me away from it. I love the stock sound and I will do a res delete with H pipe. I would prefer to keep the stock mufflers if they aren't too much...

Not ready to get tuned yet, but when I do I think it will be a Lund E85 flex tune with nGauge. I see the installs where a dash A/C vent is removed for gauge mounting. Is it possible to lose the vacuum gauge and mount the nGauge in it's place?

Looking for feedback on short throw shifters. Who has done it and which one did you go with? Impressions?