SYNC 3 swap, It's all in here

[neillv6]

Ok I did some more research and trying with Forscan. I cleared now U0238, B10B5 and B10B6 but I have still the two solar sensor error.
Can anybody help me with these?

Thanks

Hi. What I found worked for my swap from a sync 2 to a sync 3 was dl the factory as built data for your car via forscan and then adjust the little tweaks you want. It worked mostly for me. I had numerous issues and this method virtually solved it. Hth

Sponsored

 

[Epsldn]

Hello,

I know this might get asked quite a bit but I have a 2020 mustang gt base. I got my sync swap kit from a seller on eBay but it seems they sent out the gt350 bezel instead of the premium bezel. The start button, hazard, and traction control buttons work just fine. Is there anyway I can switch the last two toggles to work with my car? I haven't seen anything about this recently and figured it was worth a shot.

Everything else is working perfectly fine. I would just like to have all the switches working.

 

[salars412]

Would I need any pin swaps if I am using the Hextall or Hellhorse conversion harness. I have a 4 inch base unit that I am trying to upgrade. Also does anyone have the Ford Part Number for the GPS Antenna that I would need for this swap? Thanks in advance!

 

[Emilbadal]

No pin swaps is needed with Hextall's harness. I personally didn't use Ford's GPS antenna.

This is the one I got and it worked perfectly:
https://www.amazon.com/dp/B0107LPEWK/ref=cm_sw_r_cp_apap_sB4jCog16MzQF

Just make sure you use the metal plate base plate from your car's antenna under the new GPS antenna(showed in Hextall's installation instructions)

 

[salars412]

Thank You!!

 

[mustang_dude]

Driver Mode Enable
Mine doesn't match any of those previous codes being a Base GT Auto 2020. Does anyone have the codes for the 2020? I would like to enable drive modes since I just did a sync 3 upgrade with 8" screen.
ABS as-built 760-02-02 is showing 0200 2210 009F
IPC as-built 720-06-01 is showing 7C6F 867B 102A

 

[eXodium]

Does anyone have the main forscan changes you need to make when doing a sync 2 to sync 3 swap on a 2015 base mustang ecoboost? Thank you!

 

[Edge540je]

Just finished my install from 4" to 8" on my 2020 GT PP1 Base car.

I am so glad I worked with Thomas at HextallS550.

The unit was brand new. Bezel was new as well. The price cannot be beat plus the excellent help to program. I would not hesitate to reach out to him. I think he has some bezels available for a kit.

All functions are working flawless..

 

[salars412]

Are there any forum member discount codes for hextall and hellhorse?

 

[mustang_dude]

Just finished my install from 4" to 8" on my 2020 GT PP1 Base car.

I am so glad I worked with Thomas at HextallS550.

The unit was brand new. Bezel was new as well. The price cannot be beat plus the excellent help to program. I would not hesitate to reach out to him. I think he has some bezels available for a kit.

All functions are working flawless..

Hi, I did not purchase any parts from them, I mostly bought all of my parts from a 2019 GT premium that was totaled. I have the VIN number so I am thinking I can program that in but not sure how to approach it. I am also curious if you got Ford pass to work correctly?

 

[mustang_dude]

Try this, 726-41-01 x*xx xxxx xxxx Hazard Type 0=Latching 1=Momentary.

That worked for my 2020 Base GT, thanks i8iridium

 

[Greenerict]

Are the wire connector pictures super small for anyone else?

 

[rtrdude]

Anyone have the asbuilt codes to enable drive modes and fix hazard switch. 2020 auto

 

[RbStang22]

Id like that thank everyone for compiling all the info on this thread, Last week I swapped out my base 4.2 for Sync3 and I have been able to solve most the issues via these posts. One last issue that I cannot seem to fix: I swapped to a 2020 APIM with a Nav/Sat/HD ACM. Nav is still not working, Sirius is connected but I have zero radio reception, no AM or FM just static. I removed the factory GPSM and used a hextall harness.

I used As-Built data from a premium 2017 with HD SAT Nav for changes to the APIM and ACM. I also have the incorrect HUB but have the correct one on order. Any help would be greatly appreciated, I may have to just install my old ACM but would like to keep the NAV/SAT one.

 

[Greenerict]

Id like that thank everyone for compiling all the info on this thread, Last week I swapped out my base 4.2 for Sync3 and I have been able to solve most the issues via these posts. One last issue that I cannot seem to fix: I swapped to a 2020 APIM with a Nav/Sat/HD ACM. Nav is still not working, Sirius is connected but I have zero radio reception, no AM or FM just static. I removed the factory GPSM and used a hextall harness.

I used As-Built data from a premium 2017 with HD SAT Nav for changes to the APIM and ACM. I also have the incorrect HUB but have the correct one on order. Any help would be greatly appreciated, I may have to just install my old ACM but would like to keep the NAV/SAT one.

Did you plug in the black connector to the back of the ACM? I forgot to do this at first and the radio was all static. It's easy to forget because it doesn't have a very long wire. Edit: this is the antenna for the radio, it's different than the two multi-pin connectors.

Did the hextall harness come with a GPS antenna? It should plug into the APIM (screen) with the blue connector.

Sponsored