help

Car: Mustang GT 2017 My current performance mods are: Custom X Pipe Borla Atak Mid Pipe Straight Pipe (no muffler, catless, no resonator) Airaid MXP Cold Air Intake (2019) 2018+ Intake Manifold (w/ lockouts) My goal was to at least get another additional 15-20 rwhp. without relying on E85 &...

I want to replace the stock spoiler that is on my Mustang GT convertible to a California Special spoiler, but the only thing I am wondering is if the California Special spoiler would go into the holes that the stock one used to be held in place or would I have to install new holes into the trunk...

Hey all, I just purchased a pair of texas speed 1-7/8 304 stainless steel long tube headers with a off road connection pipe (catless). I received them today and the drivers side header has a minor bent/dent on the opening of the piping which the off road connection pipe fits over. When...

Hello, I am looking to buy new wheels for my car, was looking to get a square setup for my 2016 Ford Mustang GT 4 x ROHANA - RC22 Matte Black 20x10 +40 offset https://www.carid.com/rohana-wheels/rc22-matte-black-667163493.html 4 x TOYO TIRES® - PROXES SPORT A/S (265/35R20 Y) So, my question...

Hello everyone! This might seem an odd request but is anyone from Crossville, Tennessee or close by and willing to pick up some mufflers for me and ship them here in NJ? 😇 The seller won't ship...I'll pay for the service and shipping of course.

Ok, so I have a roushcharger stage 2 with catch can, oil pump gears, timing chain tensioners, harmonic balancer… the car is pushing 85k miles on the odometer. i blew out my clutch the other day while racing someone, ever since I replaced the clutch the car has had multiple misfire codes, p0300...

anyone knows what's that code? and how can i fixed ? my car is tuned with diablosport Please help!!! 🙏🏻

I just recently bought a JLT CAI for my 2020 mustang ecoboost HPP. Once I installed it, everything was working perfectly up until I tried to close the hood. The intake and the heat shield both seem to be not allowing the hood to fully close. Every time I can get the hood to be pushed down all...

Hey guys another issue sadly so was driving the car check engine light came on and p0300 multiple engine misfires. I have new plugs in the car about a month old. I checked the plugs all looked fine and didn’t smell like gas so I don’t think I have a bad coil. I cleared the code and it came back...

Hey guys, first time poster, does anyone have a wiring Diagram for the secondary/rear O2 Sensors that shows what colour wire goes to what pin outs on the plugs? Im trying to repair a wiring harness, thanks!

Deleted

Hi guys other day was driving my car (2015 mustang gt premium) normally not beating on it shifting below 3000rpm and I noticed the check engine light came on. Codes read P0300- multiple random misfires detected on multiple cylinders P0325- knock sensor 1 circuit bank 1 P0330- knock sensor 2...

Hi I have a 2015 mustang gt, only mods I have are a cai and a borla exhaust. Recently had my ac compressor changed and my knock sensor started reading anywhere from -1 too -9 degree depending on the rpm and gear I was in. I will point out my knock sensor always read 0.00 prior too changing my...

I purchased a 2017 mustang gt base 6 speed back in March. Has given me issues every step of the way. Installed a VMP Odin Supercharger as well as upgraded the oil pump gears. Now it's throwing codes •P0345 -Camshaft position sensor A circuit bank 2 •P0349 -Camshaft position sensor A circuit...

I have a 2020 mustang gt base and I wanna run a forgestar f14 set up preferable 20x9.5 deep concave up front with a 275 and a 20x10.5 or 11 super deep concave and run a 305 in the rear I’m on BMR drag suspension and I don’t want any stretch or camber since I do run the car hard and not a fan of...

I’m either weak af or this belt is damn near impossible to install. I have got it on once. But it wasn’t sitting on all the threads on the balancer. Also the tensioner was set at 95 instead of 100 like the manual recommends. I have the idler all the way down. am I doing something wrong here...

Just got a 2017 GT and have failed inspection (once) and the readiness test (a few times) over the past couple days. It was in transit on a truck for ~2 weeks and I have put ~150 miles on it since I picked it up. Failing on Cats, O2S, HRT Mods include C&L CAI, MBRP Catted LTH, GT350 intake...

Hi all, I need some advice and any input is greatly appreciated. I have a 19 GT 10R80 Transmission w/stock powertrain. I’m looking at going 800-900HP Forced Induction via VMP. Will run 93 octane. That’s great and all, but I’m looking at making all of that power hit the deck; reliably and...

Anybody happen to know the part number to this "snorkel" piece? I ordered the GT500 airbox and cover to help keep the IAT down for my JLT intake. I saw somebody do it, so I wanted to give it a try.

I’m in the process of adding a new differential. I have the front bolts in fine but the rear are giving me tons of resistance. To the point where it stops and I’m afraid it will snap the bolt. What are my options? I think both threads of the bushing are stripped. Can I get a tap to make fresh...