OP
OP
DFB5.0
Well-Known Member
- Thread starter
- #2,236
Polishing Continued...............................
Back on the polishers today as I continue working around the car. Today, I started on the hood, in particular the gloss black hood vent. I knew this would test my patience, so starting on it while I was still fresh made the most sense. While this part of the car looked ok from a distance, it was hazed out and dull when viewed up close. I tell someone had a go at polishing it, the dried compound the giveaway.
I'm going to be honest here, I did my best but I just couldn't get it corrected like I wanted. First, I started with Reflect on the yellow Rupes, but the marring was still present. I then tried Perfect Finish on the same pad, again, no dice. I then tried a microfiber pad with Perfect Finish, no luck there either. So, after another pass with Reflect with barely any pressure, I concluded that I was both removing and installing the marring. In the end, I gave it one last polish by hand using Carpro Essence and walked away. The black roof in comparison was easy.
This hood vent reminds me of the gloss black trunk panel on my S550, which would scratch by just looking at it. Because these gloss black trims are not actually painted, I think the only real solution for this would be to have it painted and clear-coated. It's an easy removal, so I'll have to think about it. In the meantime, I'll just coat it and try to ignore it.
I also got the glass polished today using P&S Clarity Creme. To avoid plastering glass polish all over the rubber trims, I went around the edges with a Carpro glass hand polishing block, which uses the same rayon material as their normal glass pads. I then put a Lake Country SDO Blue pad on my 3-inch ShineMate and took care of the inner sections. I really like this product, its so easy to use and does not require micromanagement like CeriGlass does, or require a sledgehammer to remove the residue afterwards. That 473ml bottle will last you the rest of your life, negating its cost.
From here, I removed the tape and began cleaning up polish residue and dust out of the cracks and crevices by using compressed air, rinse-less wash and Carpro Eraser. I also had to break out the Meguiar's M39 to remove some residue from the rear GT badge and 5.0 fender badges.
Am I 100% happy? Probably not, mainly because of that hood vent and a couple of imperfections that I will need to address. But overall, the car has taken on a much deeper, crisper tone to its paint. This is something that was noted by the guys at the dealer last week, that despite both being Race Red, they looked different side by side. That would be down to the polishing and ceramic coating that my old car got before trade, that work bringing out a more defined glass-like depth to the paint.
Up next, a thorough wipe down with a prep spray, then coating the paint, trim and glass. I then have two sets of wheels to coat. No rest for the wicked!
Back on the polishers today as I continue working around the car. Today, I started on the hood, in particular the gloss black hood vent. I knew this would test my patience, so starting on it while I was still fresh made the most sense. While this part of the car looked ok from a distance, it was hazed out and dull when viewed up close. I tell someone had a go at polishing it, the dried compound the giveaway.
I'm going to be honest here, I did my best but I just couldn't get it corrected like I wanted. First, I started with Reflect on the yellow Rupes, but the marring was still present. I then tried Perfect Finish on the same pad, again, no dice. I then tried a microfiber pad with Perfect Finish, no luck there either. So, after another pass with Reflect with barely any pressure, I concluded that I was both removing and installing the marring. In the end, I gave it one last polish by hand using Carpro Essence and walked away. The black roof in comparison was easy.
This hood vent reminds me of the gloss black trunk panel on my S550, which would scratch by just looking at it. Because these gloss black trims are not actually painted, I think the only real solution for this would be to have it painted and clear-coated. It's an easy removal, so I'll have to think about it. In the meantime, I'll just coat it and try to ignore it.
I also got the glass polished today using P&S Clarity Creme. To avoid plastering glass polish all over the rubber trims, I went around the edges with a Carpro glass hand polishing block, which uses the same rayon material as their normal glass pads. I then put a Lake Country SDO Blue pad on my 3-inch ShineMate and took care of the inner sections. I really like this product, its so easy to use and does not require micromanagement like CeriGlass does, or require a sledgehammer to remove the residue afterwards. That 473ml bottle will last you the rest of your life, negating its cost.
From here, I removed the tape and began cleaning up polish residue and dust out of the cracks and crevices by using compressed air, rinse-less wash and Carpro Eraser. I also had to break out the Meguiar's M39 to remove some residue from the rear GT badge and 5.0 fender badges.
Am I 100% happy? Probably not, mainly because of that hood vent and a couple of imperfections that I will need to address. But overall, the car has taken on a much deeper, crisper tone to its paint. This is something that was noted by the guys at the dealer last week, that despite both being Race Red, they looked different side by side. That would be down to the polishing and ceramic coating that my old car got before trade, that work bringing out a more defined glass-like depth to the paint.
Up next, a thorough wipe down with a prep spray, then coating the paint, trim and glass. I then have two sets of wheels to coat. No rest for the wicked!
Sponsored
