2018 Digital Cluster Installation Guide

[andy9111]

This will not work to change it to manual.

Well... Can I send you a DM for pricing on flashing?

Sponsored

 

[breeves002]

Well... Can I send you a DM for pricing on flashing?

I charge $299.95 for my send/return programming service and you can purchase it here: https://oemplusupgrades.com/products/digital-cluster-programming-and-support-services

 

[andy9111]

I charge $299.95 for my send/return programming service and you can purchase it here: https://oemplusupgrades.com/products/digital-cluster-programming-and-support-services

Thank!

 

[kubko]

Hi I want to ask other 15-17 owners who replaced SCCM and did programming. When you push high beam lever, will they stay activated? In my case I need to hold the lever pushed in if I want high beams to stay on. On the IPC I can see high beam light correctly when they're enabled.

On SCCM I use:
724-01-01: 0020 2600
724-04-01: 4040 0000

Thanks.

 

[Ferrcad]

Hi I want to ask other 15-17 owners who replaced SCCM and did programming. When you push high beam lever, will they stay activated? In my case I need to hold the lever pushed in if I want high beams to stay on. On the IPC I can see high beam light correctly when they're enabled.

On SCCM I use:
724-01-01: 0020 2600
724-04-01: 4040 0000

Thanks.

I have a 2015 with Dash conversion...

Mine are as follows for those two lines... My high beams work normally, push forward for on, pull for flash to pass...

724-01-01: 0020 2628
724-04-01: 4840 0000

Hope they help... GL

 

[kubko]

I have a 2015 with Dash conversion...

Mine are as follows for those two lines... My high beams work normally, push forward for on, pull for flash to pass...

724-01-01: 0020 2628
724-04-01: 4840 0000

Hope they help... GL

724-04-01: x8xx xxxx

Fixed it, works as intended now. Thanks!

 

[jjdelicious]

HELLLLPPPPPP
Attached is my code, my RPMs work, everything works perfectly except for one thing.
It’s an Manual.
I drive an Automatic and when I set it to automatic from my ABD, it changes to it but i have no working RPMs.
Please advise !

 

[Ferrcad]

The speedo came from a manual car... If so, the speedo needs flashed internally to be automatic... Will need to be sent out to be flashed with special software and file... Reach out to Breeves, he flashes for a fee... Pretty sure that is your only option unless someone else chimes in with another oppion. GL

 

[jjdelicious]

The speedo came from a manual car... If so, the speedo needs flashed internally to be automatic... Will need to be sent out to be flashed with special software and file... Reach out to Breeves, he flashes for a fee... Pretty sure that is your only option unless someone else chimes in with another oppion. GL

Hi!
No, the speedo came from an Automatic car, I just used the Baseline provided by Breeves.

 

[Ferrcad]

Well that's good news... Which line and code did you change to cause this? I'll check mine... Remember his code is only a starting point.

 

[jjdelicious]

Well that's good news... Which line and code did you change to cause this? I'll check mine... Remember his code is only a starting point.

720-03-02 CA18 000E

That value i’m currently messing witg because it changes from Auto to Manual,

auto has no working RPMs,
Manual has working RPMS…

 

[Ferrcad]

Moving to DM.. Check...

 

[BlownGP]

720-03-02 CA18 000E

That value i’m currently messing witg because it changes from Auto to Manual,

auto has no working RPMs,
Manual has working RPMS…

Is this set correctly?
I had auto cluster to and the RPMs did not work until I changed this.

720-07-02

0000

0030

CRITICAL FOR RPM

 

[BlownGP]

So, I thought I came across this years ago.

But can you change the top speed higher like the GT500?
My friend was wanting to do it. His car actually came with the digital cluster if that makes a difference.

 

[Ferrcad]

So, I thought I came across this years ago.

But can you change the top speed higher like the GT500?
My friend was wanting to do it. His car actually came with the digital cluster if that makes a difference.

Pretty sure it is hard coded in the firmware bin file of speedo. I know they have a separate file for Mach 1 assume it is the same for the GT500... may want to reach out to breeves directly....

Sponsored