2018-2019 Active Exhaust tips

[olaosunt]

I believe they are like the GT where they are attached to the muffler setup so you'd have to get the entire muffler and not just the tips. I could be wrong on that though.

You are right .
They look great though Took pic of the one at my dealer.
Much better looking than the GT 350 slip on‘s.

Sponsored

 

[armykyle1 [HACKED ACCOUNT]

hi guys new to the forum! I found these on eBay the fit well and don't require welding and look great

https://www.ebay.com/itm/Car-exhaus...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649

Looks pretty good

 

[jgilkey]

Well, it obviously wasn’t a well thought out idea on my part, but you could swap the whole muffler assembly from a Mach 1. The active exhaust hardware would transfer over. It would probably be cheaper than an after market exhaust as well.

 

[kiksbutt]

You are right .
They look great though Took pic of the one at my dealer.
Much better looking than the GT 350 slip on‘s.

waiting for someone to give us the part number

 

[PKs]

waiting for someone to give us the part number

Do you think that they will fit the 18+ valance.

 

[kiksbutt]

Do you think that they will fit the 18+ valance.

I don't see why not but I have the GT500 valance and the 5in fit fine right now.

 

[jason5.0]

Looks great. Any cutting or slip on and tighten?

They just slip on and tighten

 

[TheSnowmanMafia]

hi guys new to the forum! I found these on eBay the fit well and don't require welding and look great

https://www.ebay.com/itm/Car-exhaust-tip-3-5-Inlet-Stainless-Steel-Muffler-Pipe-Bolt-on-Design-4-OD/383706848433?ssPageName=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649

These look really good. I might try this. It's always annoyed me that the active mufflers were a 900 dollar option with terrible single wall "tips" that are totally unfinished..

 

[TheSnowmanMafia]

So those Ebay clamp on tips showed up, they look great however not a fan of the clamp. Going to dremel off the clamp and have them tack welded instead. I'll post pictures Friday when I get it done.

 

[Pitholer]

So those Ebay clamp on tips showed up, they look great however not a fan of the clamp. Going to dremel off the clamp and have them tack welded instead. I'll post pictures Friday when I get it done.

Can't wait to see the pictures

 

[jason5.0]

So those Ebay clamp on tips showed up, they look great however not a fan of the clamp. Going to dremel off the clamp and have them tack welded instead. I'll post pictures Friday when I get it done.

I would clamp them on then weld then cut off the clamp

 

[TheSnowmanMafia]

Can't wait to see the pictures

I would clamp them on then weld then cut off the clamp

The clamps didn't seem to work. The 3.5" stock tip tapers down smaller beyond the bumper and I want the new slip ons flush with the existing tips. So, in order to do that the clamp is too far past the 3.5" section to hold. If that makes sense.

My neighbor is going to help me tack weld them so I'll hold them in place while he tacks them. They'll be straight hah.

Here's a preview of them just slipped on though:

You can see the clamp on the bottom of the right most tip that also would have bothered me. Welding seems to be the way, but, the tips themselves look good to me.

 

[Vert]

The clamps didn't seem to work. The 3.5" stock tip tapers down smaller beyond the bumper and I want the new slip ons flush with the existing tips. So, in order to do that the clamp is too far past the 3.5" section to hold. If that makes sense.

My neighbor is going to help me tack weld them so I'll hold them in place while he tacks them. They'll be straight hah.

Here's a preview of them just slipped on though:

You can see the clamp on the bottom of the right most tip that also would have bothered me. Welding seems to be the way, but, the tips themselves look good to me.

Looks

 

[LightningEcoBoost]

They just slip on and tighten

Could you possibly take a close up pic of the exhaust so I can see how they fit?

 

[Salty]

The clamps didn't seem to work. The 3.5" stock tip tapers down smaller beyond the bumper and I want the new slip ons flush with the existing tips. So, in order to do that the clamp is too far past the 3.5" section to hold. If that makes sense.

My neighbor is going to help me tack weld them so I'll hold them in place while he tacks them. They'll be straight hah.

Here's a preview of them just slipped on though:

You can see the clamp on the bottom of the right most tip that also would have bothered me. Welding seems to be the way, but, the tips themselves look good to me.

Did you get around to welding the tips yet?

Sponsored