2018 Digital Cluster Installation Guide

[breeves002]

Hey, how are you?

You know I already did all this, but I've got a problem: the RPMs aren't working. Everything else is fine except the RPMs. Any idea what could be causing this? Did I forget to change something in the IPC settings?

Hope you're still around to answer this.

Programming is wrong. https://oemplusupgrades.com/products/digital-cluster-programming-and-support-services

Sponsored

 

[cryogenicdreamz]

I have a 2021 auto car i did the swap the donor car was a 21 as well swap went smooth only thing is the right lower buttons aren't working the pony and setting switches wont work when clicked what lines do I have to edit in forscan?

 

[rothrj91]

The above spreadsheet has a sample IPC and SCCM ABD you can use as a baseline for your modules.

Note: Some clusters have newer software that FORScan may not support in the latest release. If this is the case PM me for a beta build or email the forscan team for a beta build.

You must select your features and adjust the as built data as necessary. Any lines that do not have a feature set use the supplied as built data at the bottom of the page.

You must also adjust the as built data in the SCCM. You can use your old SCCM as built data except for line 724-03-01. Should be set to 1733 xxxx xx without adaptive cruise or 2933 xxxx xx with adaptive cruise.

To avoid a U2100 code in both the SCCM and IPC I recommend changing ALL ABD and then hitting "write all" at the bottom. If you are testing things, start with the baseline ABD and write all then change things one at a time. If you have the U2100 code and need to get rid of it, save your as built, change some as-built in 4+ lines, write all, then load the saved as built and write all again. Clear codes and read codes. Hopefully its gone! If you have other codes that come back after you clear codes there may be a problem with your as built data.

I believe SCCM module line 724-03-01

 

[cryogenicdreamz]

I believe SCCM module line 724-03-01

Yes that did it thanks alot now time to move on to the sync radio upgrade

 

[JDuncan]

but I've got a problem: the RPMs aren't working. Everything else is fine except the RPMs. Any idea what could be causing this? Did I forget to change something in the IPC settings?

720-07-02

0000

0030

CRITICAL FOR RPM

 

[stangnyc]

I believe SCCM module line 724-03-01

I just finished upgrading my sync 4-8 and to the digital dash. My Pony button, cruise control, Exhaust mode, phone answer/decline, radio sound is weak and settings on the dash aren’t working. Is this a programming issue or will i not be able to obtain this. Please let me know if you have an info on this.

 

[svtcarter]

Are you able to decrease miles with forscan? I wanna do the swap but having a hard time finding some with less than 18k miles and dont really wanna cough up $2000 when I could find a used one for half the cost

 

[Evolvd]

Are you able to decrease miles with forscan? I wanna do the swap but having a hard time finding some with less than 18k miles and dont really wanna cough up $2000 when I could find a used one for half the cost

No you cannot….you can only increase them with FORscan.

 

[svtcarter]

No you cannot….you can only increase them with FORscan.

well crap, I may have to bite the bullet then or get real lucky

 

[Evolvd]

well crap, I may have to bite the bullet then or get real lucky

You can buy one and send it to @breeves002 and he can change it to the correct mileage.

 

[16RPG_Turbo]

I think I'm going to end up doing this in the near future....

 

[kubko]

Does anyone know by chance if it is difficult to disassemble lens cover from the display? There are some dust particles trapped inside.

 

[Ferrcad]

Nope, I replaced mine since it came out of a wrecked vehicle and had a scratch. Four plastic clips and came right off the display. Then put the new one on. Ford part number JR3Z-10890-JA new around 15 bucks. Pull the part up and you will see the tabs. GL

 

[Whitedevil95]

Nope, I replaced mine since it came out of a wrecked vehicle and had a scratch. Four plastic clips and came right off the display. Then put the new one on. Ford part number JR3Z-10890-JA new around 15 bucks. Pull the part up and you will see the tabs. GL

Yep super easy pops right off.

 

[BlownGP]

Nope, I replaced mine since it came out of a wrecked vehicle and had a scratch. Four plastic clips and came right off the display. Then put the new one on. Ford part number JR3Z-10890-JA new around 15 bucks. Pull the part up and you will see the tabs. GL

Yup, did the same to mine.

Sponsored