Pinero's build: "Monica"

[Project Whitemare]

Killing it bro!

Sponsored

 

[pulcini011990]

Awesome build buddy im looking to go the same way with my car. Quick question though.... Where did you pick up the cobra jet manifold?

Sent from my LG-V497 using Tapatalk

 

[pinero61]

Awesome build buddy im looking to go the same way with my car. Quick question though.... Where did you pick up the cobra jet manifold?

Sent from my LG-V497 using Tapatalk

My installer ordered it, I'll have to see.

 

[pinero61]

Pinero's build: "Monica"

Took advantage of Lethal's sale:

-BMR UCA bearings
-BMR sway links
-BMR subframe bushings

This is the current list for suspension.

-BC coil overs
-BMR diff bushings
-Steeda subframe alignment kit
-Steeda G-trac brace
-OEM PP braces.
-Steeda subframe braces
-Steeda vertical links
-Steeda lower control arms
-BMR subframe lockouts
-Eibach sway bars (mid setting)

Hopefully, BMR does some hustling, and I can add a k-member to that list soon.

 

[V8Venom]

Took advantage of Lethal's sale:

-BMR UCA bearings
-BMR sway links
-BMR subframe bushings

This is the current list for suspension.

-BC coil overs
-BMR diff bushings
-Steeda subframe alignment kit
-Steeda subframe braces
-Steeda vertical links
-Steeda lower control arms
-BMR subframe lockouts
-Eibach sway bars (mid setting)

Hopefully, BMR does some hustling, and I can add a k-member to that list soon.

Nice! I am about to do the same and grab the Sway bars and end links from BMR. I still have to install my toe rods.

 

[pinero61]

Nice! I am about to do the same and grab the Sway bars and end links from BMR. I still have to install my toe rods.

You need a full set of bushings too with the power you're laying down now.

 

[V8Venom]

You need a full set of bushings too with the power you're laying down now.

Are you talking about the subframe bushings? I have diff bushings so far.

 

[pinero61]

Are you talking about the subframe bushings? I have diff bushings so far.

I still have bad hop, with my setup. That's why I got the subframe ones. I actually won't be using my lockouts now that I got those. Want them?

 

[V8Venom]

I already installed the lockout and love it. My hop is not bad at all

 

[pinero61]

I already installed the lockout and love it. My hop is not bad at all

Mine is fine up until I get on the tack.

 

[pinero61]

Okay, so I haven't updated this in some time. Here's a list of what's been completed since november:

Engine:

- CJ intake
- Twin 65 FR throttle body
- JLT cold air
- ID 1000 injectors
- Ford Racing Coil covers
- Steeda engine mounts
- Boomba trans mount
- Dyno tuning, on-going (478/419, current numbers on 93 octane)

Suspension:

- BC coilovers
- BMR LCA bearings
- BMR cradle bushings
- BMR sway links

Interior:

- Dynamat and Dynaliner applied to entire interior
- Watson Racing 4-point cage installed (custom powder coating)
- Recaro seats converted to leather.
- GT350 wheel
- Alcantara interior bits

Audio:

- Sync 2 retro fit
- Alpine inline amp
- Cerwin Vega components (front and rear)

Wheels/Tires:

- 17" Darkstars
- 19" AMR set for roadtrips.
- Mickey thompson 28" slicks

Exterior:

- APR splitter (awaiting install)
- Steeda drag wing (awaiting install)

 

[pinero61]

Here's a list of things in progress:

Engine:

- Comp RS3 cams
- PAC springs and retainers
- MMR OPG
- MMR Timing gear
- MMR secondary chains
- MMR chain guides
- Misc hardware
- E98 fuel

Drive Train:

- DSS carbon shaft
- Mcloed twin disk w/ aluminum fly

Interior:

- Autometer shift light gauge
- Aeroforce gauge
- Ngauge
- All three above to be mounted in PP dash
- Schroth 4-point ASM harness (Black)

Sponsored