Forscan EQ

[Earlsays]

I have been searching and searching, and I just cannot find which setting to change for the EQ bass roll off thing in the ACM - I tried looking in the “as built format” category, under ACM, and it says “EQ” with a value of 1

is that what I change? If not, trying to find the code to change…. Car is a base GT/small screen

Sponsored

 

[Dave2013M3]

Here you go...

This has been discussed many times. To disable factory EQ you only change the first two hex numbers to zero. Leave all other digits alone. If you changed other bits, you should set them to what they used to be. Hopefully you wrote down the original settings.
727-01-02 - 00xx "Disables Factory EQ Processing" (don't mess with xx or change anything else)

Here is a spread sheet...

 

[PICASSO]

Here you go...

This has been discussed many times. To disable factory EQ you only change the first two hex numbers to zero. Leave all other digits alone. If you changed other bits, you should set them to what they used to be. Hopefully you wrote down the original settings.
727-01-02 - 00xx "Disables Factory EQ Processing" (don't mess with xx or change anything else)

Here is a spread sheet...

I have a 2021 Mach 1 and I used Forscan to try and change ACM, My ACM already has 00xx. I have the 12 speaker B&O system. Is there a different way to change it on a 2021 model? Any help would be great. Thanks!!!!

 

[Mike Pfeifer]

I have read that the B&O is already set flat, so no need to change anything.

 

[PICASSO]

I have read that the B&O is already set flat, so no need to change anything.

Can you point me in the direction of where you got that info. I would hate to go through the trouble of installing all my new equipment if its going to sound lousy.

 

[Cathul]

https://www.f150forum.com/f30/head-unit-measurments-forscan-changes-high-level-vs-low-level-467373/

Not specific to the B&O, but shows the Sony SYNC3 and base SYNC3 measurements.
Almost all SONY Sync3 EQ settings show a flat output. If you already have a "00xx" in the corresponding ACM setting, then you don't need to do anything. Same for "0( 4, 5, 6, 7, 8, 9, A, B )xx".

With these settings all equalizing, crossovers etc. are done in the SONY/B&O amplifier, not in the ACM.

 

[Mike Pfeifer]

Can you point me in the direction of where you got that info. I would hate to go through the trouble of installing all my new equipment if its going to sound lousy.

It was in the M6G forum somewhere, but I don’t remember where exactly. I think it was someone that swapped the B&O amp into the 9 speaker system so they could get the sub output.

 

[PICASSO]

https://www.f150forum.com/f30/head-unit-measurments-forscan-changes-high-level-vs-low-level-467373/

Not specific to the B&O, but shows the Sony SYNC3 and base SYNC3 measurements.
Almost all SONY Sync3 EQ settings show a flat output. If you already have a "00xx" in the corresponding ACM setting, then you don't need to do anything. Same for "0( 4, 5, 6, 7, 8, 9, A, B )xx".

With these settings all equalizing, crossovers etc. are done in the SONY/B&O amplifier, not in the ACM.

Thanks so much!!!

 

[rojizostang]

when i made the suggested changes in forscan to disable the eq, the door chimes and chirps became insanely loud. had to switch it back.

 

[MX5Racer]

when i made the suggested changes in forscan to disable the eq, the door chimes and chirps became insanely loud. had to switch it back.

Seatbelt Reminder Chimes - Enable/Disable (turns off the
chime/sound, but does not change when the instrument cluster
light will illuminate)
IPC 720-01-01 : xxxx xx0x xxxx

Door Ajar Chimes IPC 720-01-02 : xx0x xxxx xxxx

 

[rojizostang]

Seatbelt Reminder Chimes - Enable/Disable (turns off the
chime/sound, but does not change when the instrument cluster
light will illuminate)
IPC 720-01-01 : xxxx xx0x xxxx

Door Ajar Chimes IPC 720-01-02 : xx0x xxxx xxxx

thanks

is there a way to turn off the chirp when switching channels on the radio?

 

[MX5Racer]

thanks

is there a way to turn off the chirp when switching channels on the radio?

That, I don't know..Sorry

 

[rojizostang]

That, I don't know..Sorry

it's the other thing that was extremely loud after the initial forscan change. Just thought maybe you knew. Thanks though for the other information.

 

[steathv]

You can go in the audio Settings on the in dash screen and cut the sound. Off when you change channels:

 

[Jon 5.0 2015GT]

Here you go...

This has been discussed many times. To disable factory EQ you only change the first two hex numbers to zero. Leave all other digits alone. If you changed other bits, you should set them to what they used to be. Hopefully you wrote down the original settings.
727-01-02 - 00xx "Disables Factory EQ Processing" (don't mess with xx or change anything else)

Here is a spread sheet...

Hi, I looked at the spread sheet and seen a couple of codes I’d like to change but they have a ? Mark instead of the number it can be. Do I just guess or randomly choose a number fro 0-9.

Sponsored