Search results

The GT500 comes with larger OPG but word is they are still the same powder forged material used in the GT . Any concerns with adding power ? Does anyone make a billet gear ?

I am planning a “spare “ short block for my 18 and I came across this I don’t see the the correct bore pistons offered for the 18’s but If you start off with a predator block(has the same deck surface with required knock sensors bosses )and you get a “5.4” !! Add ARP main studs and you can get a...

I am planning a “spare “ short block for my 18 and I came across this I don’t see the the correct bore pistons offered for the 18’s but If you start off with a predator block(has the same deck surface with required knock sensors bosses )and you get a “5.4” !! Add ARP main studs and you can get a...

Clearing out my garage and have a bunch of crap left over from when I swapped the 8 rib for the 6 run that was on the TVS on my 12 .(I think ) If anybody wants it let me know ,otherwise I am going to junk them . There is a cracked tensioner and it’s replacement and a bunch of smaller ones...

Less than 1000 miles

No longer need these . Link to new https://www.lethalperformance.com/arp-2013-2017-5-0l-coyote-12-point-head-stud-kit-11mm.html Came out of block that has now be converted to use the longer 12 mm ones $200 plus shipping or best offer if anyone wants them .

As stated in title-installed as part of the Stage 2 whipple on my 2018 GT . I must have got one of the earlier ones as it came with the rubber hose(instead of the corrugated one ) . It will come with the install kit that includes the corrugated hose (only thing you need out of the kit ) Looking...

I have 7 good used pistons out a failed alluminator block and a brand new one that replaced the one that had a hole . Engine builder said the used ones all checked out and I was going to use them to build a “spare” but turns out the “replacement “ Mahle had sent me was actually .005 over bore...

I have been kicking this idea around for a couple of years but I think it’s finally time to let her go . This is to just get started and I will clean thread up and add pictures as needed . Summary : New Engine - less than 1000 miles with predator based 5.2 short block /longer 12 mm ARP head...

I started cleaning out the garage for fall/winter (boo) and thought I would start with a bunch OEM fuel rails /injectors . I have two with no injectors and one with injectors I am sure came off my 15 GT’s and my sold 12 GT. I am not sure what injectors they are but they has green 0 rings ...

Last year I added the Raleigh splitter and then later the Crevini lower grill this year to my stock bumper . The splitter does not come with struts and after several passes this year the lower part of the bumper started coming apart . Replaced entire bumper with the air design and could not be...

Getting out of the " game" and getting ready to put the "race cars " up for sale after yet another round of rebuilds. No longer going to need the "spare " motors so they are also up for sale. If motors are not sold by the time I have the cars for sale , I will also offer them with the cars for...

Getting out of the " game" and getting ready to put the "race cars " for sale after yet another round of rebuilds. No longer going to need the "spare " motors so they are up for sale. Billet pro shop built 5.2 short block- New GT 350 block/ Cross plane crank. Mahle 12.1 Forged pistons and...

First rip at the track this year and first time with PBD tune /3.625 pulley/DW400 and BAP/E85 Disabled advace trac using toggles and ran in D/drag mode but torque management kept knocking timing down every shift . Made 2 passes . Went 10.17@137 with street set up and 10.0@139 with ET R’s and...

As title says . Some of you may know I started bullding “spare “ blocks to minimize down time in the event of failures . It was kind of necessary given my luck with these motors . I had BES sleeve my old alluminaor (11-14) block after melting one of the mahle pistons and replaced all of them...

Looking to free up some space in the garage Stock 18x 8.5 wheels with less than 100 miles wrapped in Dunlop 3D snow tires 265/45 rear and 235/45 front -used one season with less than 500 miles - I ended up hardly driving the car with snow tires. No shipping unless buyer wants to pay and arrange .

Since a single pump with a returnless system is rated to support 750 whp with E85. What if you do a dual pumpset up with 2 ? I am wondering if replacing the dual stock pumps in my GT 350 with the DW400’s would give me enough fuel for 850 whp on E85 without having to run dual BAPS . I don’t...

This is the second drive shaft I received from DSS. First one was replaced under warranty due to bad drive line vibration . I received the second one about 4 weeks after returning the first one . I had it installed at the same time as the stage 2 whipple . I am down to a 3.625 pulley which...

I also found these off my 12 TVS car. lids only. Great for stage 1 cars as limits boost and makes more torque. $50 each picked up.

Includes sound tube .I was about to trash them but wanted to see if anyone wants/needs them. Fifty bucks each picked up. No shipping,