ProCharger install tips and tricks

[15dib]

Yes, a slight twist should help.

I'll keep twisting it until I get the best position I suppose. Taking off the bumper was probably the biggest pain in the ass lol.

Sponsored

 

[17GT]

Pics please

 

[Bartly]

I'm in the same step I noticed it becomes kind of flat. I'm tempted to trim it abbot but I wonder if when the car starts running will it expand again.

Ha, well you are about a day ahead of me. Just getting done with the OPG and was putting the thermostat back on and thought I'd do a step towards the PC install. Sounds like it is what it is. On other vehicles I've had that lower hose would have more of a pull on it and suck flat, just wanted to see if there was a trick. Betting there is a better hose from another make/model that might fit, no time for that though, have to just get through the install.
Thanks.

 

[17GT]

Mine fit fine with a bit of twist. No trimming needed. Once you get it all together tack a pick if you have a concern. This place is a wealth of information and we will get you through it.

 

[17GT]

:doh:Take a pic, that is

 

[15dib]

I'll be doing opgs the beginning of next year. I won't be driving my car too much either way.

 

[Bartly]

Mine fit fine with a bit of twist. No trimming needed. Once you get it all together tack a pick if you have a concern. This place is a wealth of information and we will get you through it.

:doh:Take a pic, that is

I'll take a pic tomorrow, I was finishing up the OPG install and wanted to get things back together, haven't hooked the hose up yet, was just eyeballing it. Probably going to work out fine. Thanks

 

[15dib]

Well it sucks im missing a spacer for the main bracket, the 3.138" spacer. I only received one instead of two so I'm stuck.

Also I can't figure out how to bolt one of the idler pulleys. The one without he spacer I can't seem to be able to fit the 3/8 x 1-1/2 " bolt in the bracket. Am I missing something here.

 

[jabrax]

Well it sucks im missing a spacer for the main bracket, the 3.138" spacer. I only received one instead of two so I'm stuck.

Also I can't figure out how to bolt one of the idler pulleys. The one without he spacer I can't seem to be able to fit the 3/8 x 1-1/2 " bolt in the bracket. Am I missing something here.

I don't have a spacer of that size listed on my main bracket bag. I haven't ripped it open yet.

Do you have one listed and its not included, or do you need it and its not listed?

 

[15dib]

It's not listed check the paper that comes attached to the main bracket. It says 3/4" DIA x .343 I'd x3.138lspacer then it says one. Now go to page 17 on the book and it clearly shows you need two.

 

[jabrax]

We must have different packages - I have stg2 p1. It doesn't list that spacer. It list
(2) 3/4 DIA X .343 X 4.068 and another with 4.568
(1) 3/4 DIA X .250 X 1.165

and bracket instructions are 0n page 20

 

[15dib]

Oh yea mine is an ho system.
But in total you have 3 spacers which is correct mine only had two.

 

[15dib]

Ok so they send me another wrong threaded bolt. I wonder if they were in a hurry and just didn't check to well. The bolt that bolts the idler pulley closest to the top is not the correct thread. I have to go and search for one now.

 

[whatsup62]

Ok so they send me another wrong threaded bolt. I wonder if they were in a hurry and just didn't check to well. The bolt that bolts the idler pulley closest to the top is not the correct thread. I have to go and search for one now.

This should help you size it.

 

[15dib]

I matched yours with mine and I do see they forgot both that bolt and the spacer smh. I could've been finished with the install.

Sponsored