Hood Vents

[Manders Mustang]

Maybe. Though not sure a lot of America like the MY18 that much. We might find entire MY18 front ends on NTO for a handful of beans

Lol! Probably! Not sure why they're so cheap, but I'm not going to complain at all at £33 for a set! (or £55ish fully imported, but importing one on it's own costs a bob more... like £100 total or so.)

Sponsored

 

[shivatastic]

bugger annoyed I missed these but not been online much recently.

Anyone planning on doing another group buy?

Have added myself to the FB groups so I dont miss out on these again .

 

[Manders Mustang]

bugger annoyed I missed these but not been online much recently.

Anyone planning on doing another group buy?

Have added myself to the FB groups so I dont miss out on these again .

Graham has a set for sale, but you may need to repaint them. You're more than welcome to setup a group buy, or if i buy anything else from the states i'll post here give people a couple of days to add orders in (and send them to my stackry) and then keep them updated with shipping and taxes and the like.

 

[GR11M]

It'll take more than cheap hood vents to get me on FB

 

[Big_G]

[MENTION=20745]shivatastic[/MENTION] [MENTION=22410]GR11M[/MENTION]

I'm selling my set over in the classfieds, changed my mind about having them fitted.

 

[GR11M]

[MENTION=20745]shivatastic[/MENTION] [MENTION=22410]GR11M[/MENTION]

I'm selling my set over in the classfieds, changed my mind about having them fitted.

How do they fit ?

 

[Big_G]

How do they fit ?

You take your car to Modurstang (or similar trusted bodyshop), ignore the fact they whip an angle grinder out, then hand over £200 (for Modurstang) and 4 hours later you have hood vents installed.

 

[Manders Mustang]

You take your car to Modurstang (or similar trusted bodyshop), ignore the fact they whip an angle grinder out, then hand over £200 (for Modurstang) and 4 hours later you have hood vents installed.

^ in summary this, with a bit of tape, artful eye and measuring to make sure they fit flush, some sealant and some other bits along the way, but essentially, cut the hood, fit below...

They're back and gloss black now!

 

[slowhand99]

^ in summary this, with a bit of tape, artful eye and measuring to make sure they fit flush, some sealant and some other bits along the way, but essentially, cut the hood, fit below...

They're back and gloss black now

I think you should do these yourself; man of your caliber and all that........

You know the old rule; measure once, cut several times. Simple procedure.

1. Mark out, do it by eye, that's best.
2. Cut the first one
3. Cut the second one
4. Cut some more, and some more.....
5. Order new hood from Cervini's.

Piece of.......

 

[Elvis66]

You don't have to do it by eye ..you can use a piece of string and tape and a Sharpie marker.they way they completely the same on both sides.

 

[Manders Mustang]

I was thinking about closing one eye and lining it up and sticking my tounge out for extra focus. ;)

 

[Elvis66]

Well if that does not work ..least you will clean the bugs off the car lol

 

[Manders Mustang]

Well if that does not work ..least you will clean the bugs off the car lol

Lolololol, wont be any car for the bugs to be on!!! :lol:

 

[GR11M]

There's the cut outs in the second skin, with all the holes ti fit them in, you cut the top skin and fit them in, pic below, also, if you check the cover on the hood, just peel back a corner you'll see the spots for them.

Did you have to cut a hole in the bonnet liner ?

 

[Manders Mustang]

Did you have to cut a hole in the bonnet liner ?

They go on my car next week, aint got a clue, would assume so.

Sponsored