Fender liner push pins...

[Unbridled5.0]

The Ford parts counter guys (bless their hearts) have tried and failed THREE times to get me the ones I need. Can anyone here provide a part number?

I only need that one where the redneck ziptie engineering action is going on. Mine are missing on both sides and those are different than most of the others in the fenders. BIG thank you to anyone who can help. I don't want to order a generic bag of 250 push pins from amazon. I need the correct oem part. Ocd is a hell of a disease.

Sponsored

 

[delz05]

Sorry, picture gives no detail of which ones you need... Do you want the smaller ones that align the shell (about 10 of them I believe) or the larger ones that afix to the front splash pan, the rocker and lower front bumper cover (4 IIRC)? And which car do you need these for?

 

[Unbridled5.0]

Sorry, picture gives no detail of which ones you need... Do you want the smaller ones that align the shell (about 10 of them I believe) or the larger ones that afix to the front splash pan, the rocker and lower front bumper cover (4 IIRC)? And which car do you need these for?

Yeah the picture isn't great. That's my bad. It's hard to see but it's at the back, lower edge of the splash shield. It's the 3rd pin along the bottom going toward the center of the car. You have to zoom in to see it. It has a zip tie in it.

I believe it's the 'one-off' push pin that's not like any of the others in the wheel well. '22 GT.

I think it's the lone pin in the package that LMR sells for $20.

 

[646bullitt]

I am not sure which ones you need, hard to tell from your picture. But this diagram will help you out, part numbers are down below:

https://parts.southlakeford.com/a/F...1-UtOFjdKUJXk7T6I_i8L8ZD2H04Mh4ltwcT2hpDvrj_0

 

[Trout1]

The Ford parts counter guys (bless their hearts) have tried and failed THREE times to get me the ones I need. Can anyone here provide a part number?

I only need that one where the redneck ziptie engineering action is going on. Mine are missing on both sides and those are different than most of the others in the fenders. BIG thank you to anyone who can help. I don't want to order a generic bag of 250 push pins from amazon. I need the correct oem part. Ocd is a hell of a disease.

Order a push pin kit from Amazon it comes with a push pin removal tool and an assortment of sizes.

 

[WItoTX]

Yeah tell your OCD to fuck off and order off Amazon and not stress about it. That's what I've done, track my car multiple times a month, and never lost an Amazon one on track. Now....when I remove them and set them on the garage floor on a neat pile, without fail one of them walks off.

 

[GTP]

There is an old thread with the same frustration. Good advice in it plus PNs.

Perhaps try advanced search for keywords Fender, Liner, Rivet, Pin, etc.

I checked my bookmarks but didn't see one for it.

 

[Skye]

Enclosed are threads referencing OEM PN#s. There appears to be an 8mm and a 10mm.

I recently removed and re-inserted mine during a fender flap install. I can confirm there are two different sizes.

Most parts stores will carry small packs of these. Harbor Freight and Amazon will sell boxes of them.

While securing a push-pin source, buy some tools to help with removal and replacing.

https://www.mustang6g.com/forums/threads/fender-liner-to-belly-pan-push-pins.201471/

https://www.mustang6g.com/forums/th...-different-wheel-well-liners-pushpins.190733/

https://www.mustang6g.com/forums/threads/fender-clip-missing-any-ideas-which-part-i-need.185634/

Sponsored