Cobra Jet intake install

[juk15gt]

just got the tune installed and went for a ride. Nice!!!!! I will be doing some logging this week and sending back the information to Lund. Very nice tune so far! Great job Lund Racing!!!!!!! Thanks again RBS550, Lund Racing and Ramsey's Performance in Lutz, Fl.

Sponsored

 

[RBS550]

just got the tune installed and went for a ride. Nice!!!!! I will be doing some logging this week and sending back the information to Lund. Very nice tune so far! Great job Lund Racing!!!!!!! Thanks again RBS550, Lund Racing and Ramsey's Performance in Lutz, Fl.

I'm glad you're on the way!! I'm glad to inspire and help, but at times even I need inspiration and guidance and that I will get from people like you.

 

[pinero61]

Just started on my setup too!

I went twin 65, and will be adding cams soon. I have a road race oriented build, but I'll definitely have track numbers to show as well.

 

[RBS550]

Just started on my setup too!

I went twin 65, and will be adding cams soon. I have a road race oriented build, but I'll definitely have track numbers to show as well.

SWEET!! I think twin is the way to go. I can't wait to do cams either!

 

[Grimace427]

Just started on my setup too!

I went twin 65, and will be adding cams soon. I have a road race oriented build, but I'll definitely have track numbers to show as well.

Make sure to upgrade the oil pump gears while you are working on those cams.

 

[RBS550]

Make sure to upgrade the oil pump gears while you are working on those cams.

Thank you for making sure I do that, early on I upgraded the oil pump & crank gear, my weak link now should be my rods.

 

[RBS550]

Make sure to upgrade the oil pump gears while you are working on those cams.

I'm sorry, I forgot what thread I was on, you probably meant that for Sinister. :doh:

 

[beefcake]

we have blower and n/a sets on order from comp couple sets of each stage

 

[Sinister]

I'm sorry, I forgot what thread I was on, you probably meant that for Sinister. :doh:

I will definitely be upgrading both as well when I do cams!

we have blower and n/a sets on order from comp couple sets of each stage

Price on the n/a Stage 3?

 

[pinero61]

Very interested in those cams!

I'll do gears at the same time, but I have a 2012 5.0 sitting at the speed shop begging to made into a built short block.

 

[RBS550]

Update....11.11!!!

I ran an 11.11 1.520 60' @ 126.14!!! Here's a video, I have more angles but Taco Bell is slow for uploading. Staying at a motel, will run again tomorrow, hopefully 11.0s!

[ame]

 

[RockStang]

I ran an 11.11 1.520 60' @ 126.14!!! Here's a video, I have more angles but Taco Bell is slow for uploading. Staying at a motel, will run again tomorrow, hopefully 11.0s!

:eyebulge:That is simply OUTSTANDING for your mods. Congrats man

 

[Sinister]

Keep fighting the good fight my man! My E85 tune is dialed in and I should be hitting the dyno early this week and to the track the following.

 

[RBS550]

Here's a few more videos. In the first one you can see I pushed a little before the launch, little stuff like that kills you from getting your magic number. You can also see how I barely inch forward to stage as shallow as possible. The second one shows how relatively easy I take off, if I had slicks (which are lighter) a transbrake and an aluminum drive shaft I'd definitely be faster. And the third is a dash cam view.

[ame]

[ame]

[ame]

 

[RBS550]

I'm only showing the launch rpms to protect my Tuners hard work. You can see how I ramp/flash the converter just before launch. One day I'll get my JMS Launch control on and try that, but I can't imagine getting much more out of these DRs for an N/A car.

Sponsored