What did you do to your Mach 1 today

[Mikepol2]

Checked the mail

let the fun begin!

Hope you find this helpful:

https://www.mustang6g.com/forums/threads/upgraded-sway-bars-for-mach-1.193630/page-6#post-3931736

After 4 trials with various sway bar hole combinations I settled on 2nd from the front hole on the front bar (2nd stiffest) and rear hole on the rear bar (softest). Honestly if I had to do it all over again I would keep the factory rear HP bar and just use the Steeda front. @shogun32 recommended something similar before I began the whole process and after all the trials I agree. The oversteer is pretty substantial with the Steeda rear bar.

Sponsored

 

[MACHtobers Very Own]

Hope you find this helpful:

https://www.mustang6g.com/forums/threads/upgraded-sway-bars-for-mach-1.193630/page-6#post-3931736

After 4 trials with various sway bar hole combinations I settled on 2nd from the front hole on the front bar (2nd stiffest) and rear hole on the rear bar (softest). Honestly if I had to do it all over again I would keep the factory rear HP bar and just use the Steeda front. @shogun32 recommended something similar before I began the whole process and after all the trials I agree. The oversteer is pretty substantial with the Steeda rear bar.

Oversteer bad even with the settings you used? Dual rate springs or factory?

 

[shogun32]

just use the Steeda front. @shogun32 recommended something similar before I began the whole process and after all the trials I agree.

Can I get an Amen? Now where did I leave the collection plate?

 

[Mikepol2]

Oversteer bad even with the settings you used? Dual rate springs or factory?

Factory springs, bad oversteer with rear full soft and front 2nd stiff.

 

[JetGray_Mach1]

Changed my oil yesterday. Fat the tires look

 

[AZ_Ryan]

Changed my oil yesterday. Fat the tires look

Nice lift.

 

[fast306stang]

Had 2 small dings in the passenger quarter panel that I've been living with, but I got a real good ding in the hood the other day when I was coming home on the interstate when I picked the car up from the dealership for the axle clicking. That's what I get for driving behind the 3 cars poking around in the fast lane instead of passing them like I normally would.

Anyway, got all 3 dings taken out yesterday for a grand total of $100. Since I had the day off anyway, I treated myself to a killer Mexican lunch, and a cold beer at home with the music cranked and I worked on my resume for 6 hours. So yesterday was a productive day...

Car looks good, can't see where the dings ever existed.

 

[Prodigal]

Pulled the bumper and belly pan in one piece, solo!!!!……. Little tense but not bad overall. I may separate them for install.

Got a video of the how to?

 

[Mach ! Madness]

Changed my oil yesterday. Fat the tires look

What brand is your lift and do you recommend it .

 

[JetGray_Mach1]

What brand is your lift and do you recommend it .

Yes highly recommended it lifts the car up more than most jack stands can. It works flawless every time no issues. Its a Quickjack 5000TL I got it from Costco for 1400.

 

[Mach ! Madness]

Thank you .

 

[Rael]

Had a Steeda H-pipe installed.
Sublime.

 

[ChitownStang]

Had a Steeda H-pipe installed.
Sublime.

Yeah, it really is perfect imo

 

[Mjschneidy]

Drove the snot out of it for three days straight

 

[fast306stang]

NGL, replacing splitter rivets with an undersized pop rivet gun is a bitch. Especially doing it on your back. I had to disassemble the gun to get the stem out everytime.

Sponsored