ESS Centrifugal Mustang Superchargers

[80FoxCoupe]

Blower inlet will collapse a silicone 90.

Sponsored

 

[80FoxCoupe]

Try to source an aluminum or polymer elbow.

 

[Proshop]

Blower inlet will collapse a silicone 90.

Ughh I wondered..

 

[SheepDog]

Isn't the ESS inlet tube silicone? or does it have some sort of rigid structure?

 

[Proshop]

Isn't the ESS inlet tube silicone? or does it have some sort of rigid structure?

It is silicone…

 

[SheepDog]

It is silicone…

Looks like it necks down to 3.5" also where it meets the Blower.

You could just do an aluminum elbow, and then use a reducer coupler.

https://www.siliconeintakes.com/aluminum-pipes/aluminum-pipe-p-778.html
You don't need the knurled ends since there isn't any outward pressure inside the tube, so just cut to fit.

https://www.siliconeintakes.com/intake-pipe-reducer/pipe-reducer-p-539.html

 

[Proshop]

Looks like it necks down to 3.5" also where it meets the Blower.

You could just do an aluminum elbow, and then use a reducer coupler.

https://www.siliconeintakes.com/aluminum-pipes/aluminum-pipe-p-778.html
You don't need the knurled ends since there isn't any outward pressure inside the tube, so just cut to fit.

https://www.siliconeintakes.com/intake-pipe-reducer/pipe-reducer-p-539.html

I think it’s like 3.75”

 

[SheepDog]

They also make carbon fiber pieces, if you want to get fancy but only up to 3.5" diameter

https://www.siliconeintakes.com/aluminum-pipes/carbon-fiber-90-p-9672.html

 

[SheepDog]

I think it’s like 3.75”

https://www.siliconeintakes.com/intake-pipe-reducer/pipe-reducer-p-541.html

 

[Proshop]

They also make carbon fiber pieces, if you want to get fancy but only up to 3.5" diameter

https://www.siliconeintakes.com/aluminum-pipes/carbon-fiber-90-p-9672.html

Damn that is fancy!

 

[SheepDog]

Damn that is fancy!

Lol. You could use a straight 4" section of aluminum from the filter, then use a 4" - 3.5" reducer to connect the Carbon elbow, then a 3.5" - 3.75" to connect to the blower. Then you could just remove the elbow section when you want to run the screen and leave the rest of the assembly in the car.

 

[Proshop]

@SheepDog is this the T CC you were talking about?
https://www.uprproducts.com/15-21-mustang-gt-5-0-billet-breather-tank-plug-n-play/

 

[SheepDog]

@SheepDog is this the T CC you were talking about?
https://www.uprproducts.com/15-21-mustang-gt-5-0-billet-breather-tank-plug-n-play/

Similar, however the fittings were different in that the short section of hose attached to the catch can instead of the passenger side PCV.

 

[SheepDog]

It would definitely work though

 

[Proshop]

Similar, however the fittings were different in that the short section of hose attached to the catch can instead of the passenger side PCV.

I see what you’re saying! So not sure if it has been discussed and I missed it or not. Do you think two cans are better than one? Could one manifold vent fight the other and cause oil and vapors to push back or hold back from one side? Basically two opposing forces fighting each other and the stronger of the two wins.

Sponsored