Mach 1 Rear-wheel lip molding part number

[ChitownStang]

Ok, the the double AA
Seems like I almost got the ones with the single A
Thanks

Sponsored

 

[MLO 351]

Ok, the the double AA
Seems like I almost got the ones with the single A
Thanks

What's the difference?

 

[ChitownStang]

What's the difference?

called mud guards. maybe for gt350

 

[MLO 351]

called mud guards. maybe for gt350

Thanks, do you know if there's any difference in how they look or fit?

 

[ChitownStang]

Thanks, do you know if there's any difference in how they look or fit?

no idea, I'm pretty confused already! lol
I think I read that one of them doesn't match the texture of our cars plastic on the rear bumper

 

[MLO 351]

no idea, I'm pretty confused already! lol
I think I read that one of them doesn't match the texture of our cars plastic on the rear bumper

I've got a pair of these below, not fitted yet.

FR3Z-6328371-A

FR3Z-6328370-A

 

[melwff]

I've got a pair of these below, not fitted yet.

FR3Z-6328371-A

FR3Z-6328370-A

They are wrong. I made the same mistake. They fit the GT350. They will physically attach to the car but the bottom edge does not correctly align with the bottom of the rear bumper.

 

[MLO 351]

They are wrong. I made the same mistake. They fit the GT350. They will physically attach to the car but the bottom edge does not correctly align with the bottom of the rear bumper.

Thanks Melwff, do you know if they can be modified to fit or is the GT500 version the only option?

 

[melwff]

Thanks Melwff, do you know if they can be modified to fit or is the GT500 version the only option?

The cutout on the bottom of them just doesn't match up correctly. Try it you will see the difference.

 

[Charlemagne]

Also looks like the spreadsheet show part # for the screws starts with 715 and your screw shows 716

It probably doesn't matter, both are arch screws.
See the numbers listed for GT500 version (the correct one for Mach 1) in this diffusor kit:
https://www.levittownfordparts.com/sku/gt500diffuserkit.html
Shows W715060-S450B screws.

The GT350 version shows W716195-S450B... screws. As said, GT350 guards do not fit, but the screws and clips apparently do.
https://www.levittownfordparts.com/sku/splshgrdkit.html

Since @melwff got first the GT350 version which didn't fit, he had the screws and clips and used those with just the guards for GT500. I got what's listed in the spreadsheet, haven't got to installing it yet, though. Mach 1 has GT500 diffusor so makes sense these fit.

 

[pappagray]

I don't care to read the whole thread. But I went through this My Mach was missing the Right rear. Gt350 ones are wrong as mentioned. Here is aprt number for RR Kr3z-6328370-aa

 

[Xpdwheel]

I just completed installation of the rears on my non-HP Mach 1. Took about 20 minutes per side. Jacked up one side of the rear to get additional clearance. Popped the three plastic retainers that hold the wheel well liner and moved it out of the way. Removed two existing screws that hold side of bumper. Installed two screw clips into existing holes, located molding pin into existing hole, replaced original screws plus two new ones, replaced liner into original position, reinstalled original three plastic retainers plus one new one. Only tools used were small screwdriver and 1/4" ratchet with short extension and socket.

I know this is an older thread but can you clarify which rear splash guards you installed on the Mach 1?? Was it the gt500 rear set??
I ordered rokblokz gt350 front/rears, guess there going back. Thanks..

 

[Charlemagne]

The GT500 rear set works fine (it's GT500 diffusor after all), I have them on my car.

 

[melwff]

I know this is an older thread but can you clarify which rear splash guards you installed on the Mach 1?? Was it the gt500 rear set??
I ordered rokblokz gt350 front/rears, guess there going back. Thanks..

GT350 are not correct for Mach 1, as already pointed out it uses GT500.

 

[Xpdwheel]

GT350 are not correct for Mach 1, as already pointed out it uses GT500.

Thanks

Sponsored