[?] '18 Intake Manifold on '15-'17

[Demon Coyote]

Plenty of options out there. But knowing how they work saved me from spending extra money or messing with the manifold at all. Just do what will give you peace of mind.

Sponsored

 

[Jay-rod427]

Home Depot! pfft I run a machine shop using aluminum. Just don't know what it needs to be until I get the manifold hopefully later this week.

 

[aleccesarenriquez]

So the ridiculously overpriced lockouts aren't even needed?

MMR intended them to be for boosted applications. At least that's what their website says.

 

[Draklia]

Home Depot! pfft I run a machine shop using aluminum. Just don't know what it needs to be until I get the manifold hopefully later this week.

If you end up making some can you post up the dimensions (hole spacing)?

 

[Joe 5.0]

Home Depot! pfft I run a machine shop using aluminum. Just don't know what it needs to be until I get the manifold hopefully later this week.

How much to make me a set? :shrug:

 

[Jay-rod427]

Soon as I get something whipped up I will gladly share.

 

[Joe 5.0]

Soon as I get something whipped up I will gladly share.

You're the man. Thank you!

 

[5ABI VT]

So does anyone have working imrc with the 18 manifold ? I picked up harness adapters (think someone on the forum made them) but I couldn’t find the person or the thread if there is one and have the 18 mani. Don’t want to deal with codes and don’t want to lockout either.

 

[Red5.0]

I installed the 18 manifold with the blow by racing imrc y harness pigtails with Lund tune. I have driven the car for about 50 miles and so far so good. Keeping my fingers crossed. Will update when I have more miles on the car.

 

[2016GTM6]

I installed the 18 manifold with the blow by racing imrc y harness pigtails with Lund tune. I have driven the car for about 50 miles and so far so good. Keeping my fingers crossed. Will update when I have more miles on the car.

That's the same harness I have but I ordered lockouts after reading all this on the forums. I decided I don't want the hassle to have to pull the intake again so I'm just going to lock them out from the beginning

 

[Joe 5.0]

That's the same harness I have but I ordered lockouts after reading all this on the forums. I decided I don't want the hassle to have to pull the intake again so I'm just going to lock them out from the beginning

Good move! Avoid the hassle from the beginning.

 

[5ABI VT]

I installed the 18 manifold with the blow by racing imrc y harness pigtails with Lund tune. I have driven the car for about 50 miles and so far so good. Keeping my fingers crossed. Will update when I have more miles on the car.

Any updates? If Lund can tune it and imrc works without codes I will go with lund as well. Are you using the stock tb? :cheers:

 

[Nuked]

Got longtubes on and did a dyno pull. Mods below. It's a low reading dyno, owner said that is pretty good number on his dyno. Runs good, definitely tell an improvement from the long tubes.

Untitled by https://www.flickr.com/photos/94850774@N07/

2016 GT Performance Pack
Lund Flex tune
Corsa longtubes
Corsa Sport catback
2018 Manifold IMRC locked out
JLT intake
52lb Ford Racing injectors
E85

 

[Red5.0]

Any updates? If Lund can tune it and imrc works without codes I will go with lund as well. Are you using the stock tb? :cheers:

Put about 80 miles on the car so far and no check engine light. And yes I am using the stock tb.

 

[Dr. Norts]

Got longtubes on and did a dyno pull. Mods below. It's a low reading dyno, owner said that is pretty good number on his dyno. Runs good, definitely tell an improvement from the long tubes.

Untitled by https://www.flickr.com/photos/94850774@N07/

2016 GT Performance Pack
Lund Flex tune
Corsa longtubes
Corsa Sport catback
2018 Manifold IMRC locked out
JLT intake
52lb Ford Racing injectors
E85

Thats a pretty sharp drop off in torque around 3150 rpm.

Sponsored