UPR Oil Catch for PC install?

[venumous]

Does anyone have any kind of installation material on the UPR oil catch for the Procharger? I got mine from Beefcake and there isn't so much as a piece of paper in the box with it.

Sponsored

 

[Tommy V]

Yea alot of guys are saying that,thats crazy!!!.I would check and see if CJ Pony has an install video of it.I think its a pretty easy install though.

 

[UPRSteve]

Shoot me an email at [email protected] and I can send them

 

[15GTPP]

Let's see if this helps you out. I was confused with the instructions as well.
The green line is the imrc tube. Use the smaller tee to connect to imrc line to the line coming off the driver side valve cover. The Blue t will be where you put the second tee. The yellow line is the hose coming from the passenger side valve cover and connects to that blue tee.. The teal line is the line that comes straight from the intake and plugs into the catch can. You will have to cut lines and my kit even came with an extra connector.

 

[venumous]

Thanks guys!!!

 

[whatsup62]

Hers is the instructions and a crude photo of how I had it.

Red line hose - pass side dirty line under coolant tank, under radiator cover to drivers side. Solid red rectangle where the hose connector is taking it to the tee (red circle). Other side of tee goes to top of catch can.

Yellow line hose - drivers side dirty line going to fist tee (1/2" x 3/8" x 1/2" tee ,yellow circle) then to second tee (1/2" x 1/2" x1/2" tee, red circle).

Pink line hose is the small 3/8" vent hose from IMRC factory Y to 1/2" x 3/8" x 1/2" tee.

Blue hose - clean line from catch can to Procharger air intake tube fitting.

The kit does not come with the tee's , hose connector , or single connection point on the PC air inlet tube. These where all local auto part store pieces.

 

[venumous]

Got it all hooked up. Thanks again guys.

 

[Phill The Greek]

Whatsup62, you noted the specs on the tees needed but do you happen to have any specs or pics of the additional install parts needed? I'm a total newb and my UPR can hasn't been delivered yet.

"The kit does not come with the tee's , hose connector , or single connection point on the PC air inlet tube. These where all local auto part store pieces"

Thanks

 

[15GTPP]

If you have the lines setup like it tells you to do it in the procharger manual you should have everything you need to install the catch can. I had everything I needed to install it. The T's come in the procharger kit.

 

[Phill The Greek]

If you have the lines setup like it tells you to do it in the procharger manual you should have everything you need to install the catch can. I had everything I needed to install it. The T's come in the procharger kit.

Thanks.

So with the proc harder kit already installed I'll only need to run the hoses to the right points and connect to the already in place hardware?

 

[Phill The Greek]

Damn autocorrect. Procharger

 

[15GTPP]

The catch can comes with all completely new hardware(hoses and oem style connectors) only thing you will be reusing is the T's. Install can get a bit confusing but if you look at the two guides above you can get through it. You will have to cut hoses and might even have an extra connector.

 

[raider5oh]

I installed mine a few weeks back. I was upset at how the mounting bracket is a little too short and I had to bend the metal lines by the strut tower for it to fit right. Still doesnt sit level. Also to empty it I have to loosen the metal fittings or the top won't come off cause it catches the metal filter lip. I'm probably just going to put a stainless steel drain line on the bottom to make things easier.

 

[whatsup62]

I installed mine a few weeks back. I was upset at how the mounting bracket is a little too short and I had to bend the metal lines by the strut tower for it to fit right. Still doesnt sit level. Also to empty it I have to loosen the metal fittings or the top won't come off cause it catches the metal filter lip. I'm probably just going to put a stainless steel drain line on the bottom to make things easier.

Yes..that was an issue. I ended up pulling it off each time I would need to drain it.

 

[Phill The Greek]

How do you drain this thing? Everything is super torqued down and I'm not sure if the whole can should be unscrewed and dumped or if you are supposed to just undo the square plug at the bottomoment to drain it. Any help is appreciated.

Sponsored