intercooler installed, now CEL

[Jesse R]

I think it has something to do with the ground strap. Did you put it on top or bottom

For the clean side catch can? I didn't notice it had one nor did I see anything about it on the crappy instructions posted.

For the Dual valve catch can I installed I put it on the top like the directions said but that was about a year ago..I doubt it would be bringing up A cel now.

I'm gonna go double check both catch cans now

Sponsored

 

[Jesse R]

Strap is on top..checked all my connections. Everything is tight so I cleared the code with the scanner and pulled the negative terminal on the battery for a while..we will see if the code comes back on.

 

[doulos4jc]

I'm installing the CP-e IC in a couple weeks and plan on a grill shutter delete at the same time. Is there some info on the forums for this, I searched but couldn't find. Thnx

 

[Busser48]

I'm installing the CP-e IC in a couple weeks and plan on a grill shutter delete at the same time. Is there some info on the forums for this, I searched but couldn't find. Thnx

Yea just pull the shutters off, make sure not to leave sensor unplugged, some will get a code some won't.

 

[Jesse R]

Yea just pull the shutters off, make sure not to leave sensor unplugged, some will get a code some won't.

Do you know what the code is for shutter system being removed. Just incase that pops up sooner or later

 

[rvercitypony]

If you're removing the ACC you can install a larger intercooler than the cp-e unit. I got it because it was the largest I could find and still retain the ACS.

 

[JStang15]

Strap is on top..checked all my connections. Everything is tight so I cleared the code with the scanner and pulled the negative terminal on the battery for a while..we will see if the code comes back on.

The code will probably come back. I got the same code after installing my CSCC. I cleared it but it came back pretty quickly. Ended up having Adam just disable it in my tune. From what I understand, it won't cause any harm. It just happens because the sensor (the VPS sensor I believe) on the clean side isn't seeing as much flow/pressure once the can is installed.

 

[Jesse R]

The code will probably come back. I got the same code after installing my CSCC. I cleared it but it came back pretty quickly. Ended up having Adam just disable it in my tune. From what I understand, it won't cause any harm. It just happens because the sensor (the VPS sensor I believe) on the clean side isn't seeing as much flow/pressure once the can is installed.

I might end up ditching the cscc then. I'm not in the market for a tune yet.

 

[JStang15]

I might end up ditching the cscc then. I'm not in the market for a tune yet.

Yeah I hear you. If I didn't already have a tune I probably would've taken it off.

 

[whirledpeaz]

Do you know what the code is for shutter system being removed. Just in case that pops up sooner or later

If you pull everything off, it won't cause a CEL but the ECM can store one (or more?) of these. If you don't want to see it when you scan for codes, just leave the motor plugged in.

P059F Active Grille Air Shutter "A" Performance / Stuck Off
P05A1 Active Grille Air Shutter "A" Position Sensor Minimum / Maximum Stop Performance
P05A2 Active Grille Air Shutter "A" Control Circuit / Open
P05A7 Active Grille Air Shutter Control Module "A" Supply Voltage Circuit Low
P05C0 Active Grille Air Shutter Module “A” Over Temperature
U0284 Lost Communication With Active Grille Air Shutter Module "A" ( I had this one when I removed the ags on my focus st )

 

[JGato]

No cel with grill shutters removed and eBay intercooler. Sensor left unplugged.

Sponsored