Comp cams?

[beefcake]

just depends on skill level

Sponsored

 

[Dominant1]

My stage 3 comp cams build was stalled by my circle d "stall" speed converter being defective...lol and since the circle d guys had no 5c's on the shelf to send right out to my tuner, it had to be sent back to be repaired. they shipped it to Jpc last thursday ground rather then today. it should have arrived 2 day, so They'll put it in and start the tuning phase of my build. Shit happens guys as you know but i should have some numbers for you guys soon....

 

[Performance nut]

I'm looking for driveability with some gain. The only dynos I found showed bottom losing for stage 2 and losing alot for stage 3. Like sub 300ft-lb until 3000-4000RPM. Not sure if it's a move I want to do on a DD. Might have been the tune or another factor though.

Still waiting on a stage 1, see if it increases the lower band with a bump in peak.

 

[GSLSE20B]

AED just ran 11.3@121 with custom cams , hopefully other people will have better luck

 

[dubster99]

AED just ran 11.3@121 with custom cams , hopefully other people will have better luck

Yikes. I'm assuming those were the cams Shaun had a hand in designing? Your driver mod trumps all I guess! haha

 

[Dominant1]

Low end torque at lower rpm is of little concern to me when you couple cams with a circle d 5c converter. When you go wot it instantly jumps right into your sweerspot and pulls insanely hard to 7800 rpm. This is what i want ..if you tried to use the stock converter with these cams you will feel the reduced torque alot more! Besides when roll racing your kicking it down at 3500-4000 rpm which is the begining of your sweetspot! Stall speed converters are a must with cams, and i wouldnt have it any other way!

 

[1320']

AED just ran 11.3@121 with custom cams , hopefully other people will have better luck

Yeah I saw that..holy crap.

That man works magic on Coyotes...I swear.

 

[Dominant1]

Update: Just got word 30 minutes ago, my car is next in line for the dyno, if not Tomorrow definitely Monday it should be done.....

 

[olsonjus]

Do you have a baseline to compare what power it made precams?

 

[Dominant1]

Do you have a baseline to compare what power it made precams?

No i don't, the guys at Jpc Jumped right on the build. but these cars make 365-375 rwhp stock, i had a catback to it so maybe 5 more rwhp from that....i'm guessing when its all said and done it should be about 485-500 rwhp... and that's a good neighborhood..

 

[Joe 5.0]

No i don't, the guys at Jpc Jumped right on the build. but these cars make 365-375 rwhp stock, i had a catback to it so maybe 5 more rwhp from that....i'm guessing when its all said and done it should be about 485-500 rwhp... and that's a good neighborhood..

I would love to see 500rwhp!!! :ford:

 

[sandeale]

Im almost as excited as you are for these results, if these cams put out like a cheap date, my credit card will receive punishment

 

[beefcake]

rev auto seems to like them, they just picked up another set from us today. they have done quite a few builds with them

 

[Dominant1]

rev auto seems to like them, they just picked up another set from us today. they have done quite a few builds with them

Beef everyone gets them from you, your the only one that stocks them, in fact rev auto ordered mine from you back in july.

 

[beefcake]

Beef everyone gets them from you, your the only one that stocks them, in fact rev auto ordered mine from you back in july.

Sponsored