Need the stock exhaust for a 2015-2017 GT. Im in San Antonio but can travel a few hours to pick up if need be. Let me know if there is anything out there!
Are the instructions for removing the timing chains and reinstalling them the same for the voodoo as they are on the coyote? About to install a GT500 oil pan and pump on a buddies 350. I have done like 10 or so OPG installs on the coyotes motor but never on the voodoo.
The FCIM (Front Control Interface Module) or Radio Bezel, not sure why they don't just call it that, on my 2016 GT Premium is dying. Anyone have a one laying around they can sell me. I need the one with the Heated and Cooled Seat buttons like in the picture. Sorry TheHydro I borrowed the...
Whats up S550 family.
Helping my buddy get his Fore Fuel system installed July 4th weekend and need some guidance on where to grab the boost/vac reference from. Had him go ahead and purchase the Fore vacuum block which we will use to feed the vac source on the fuel pressure reg and the hobbs...
Hey All,
Those of you with fuel systems with the fuel rails run in parallel, where did you place the "Y" for the feed? Can anyone provide a picture of where you did?
Thanks!
Josh
Hey guys!
Getting ready to install a fore fuel system and get a custom tune. Tuner has requested that Intercooler pump be wired to a keyed source. The stock relay from Whipple uses one of the IMRC plugs for its keyed source. I assume this plug can be cut off the relay and one of the wires be...
About to do a short block swap and had a question about head gaskets. Does cometic not offer a head gasket for the Gen 2 coyote? The oil hole is bigger for the cam phaser oil passage on the gen 2 and ford specifically calls out the gen 1 gaskets not working correctly because of this.
Any ideas?
Finally got the car on the rollers and I think I did ok?
Car has the Whipple stage 2 running the stock whipple tune. Have stainless long tubes with cats and stainless works retro catback.
Thoughts?
So... I recently ditched my ProCharger setup after fighting for almost two months to find false knock. After a few weeks of driving around with a slow car I got the itch to get boost again and finally pulled the trigger on a Stage 2 Whipple Kit from Lethal Performance. I got everything installed...
Hey All!
Have my Whipple kit coming in next week and need to return my car to the stock tune before loading the Whipple provided tune. I remember at some point telling my nGauge to read the car again which saved a new stock tune file that was really a pro-charger tune (I had a CEL that I was...
Hey guys,
Did a bunch of part installs yesterday and ran into a little issue. While installing the front insert, I stripped the threads that hold the insert inside the OE bushing. The smaller bolt that goes through the Diff into the OE bushing is just fine as I was able to get the torque wrench...
Hey All,
I've been running my Procharger HO setup for a few weeks and it runs GREAT except for one little issue. If I am around 2500 RPMs or so and get the pedal to about 60 percent the car surges multiple times until you either A. Let off the throttle, B. Go WOT, or C. Pass 3000 RPMs.
Here...
Hey all,
Finally got my Procharger P1SC installed. Setup is the HO tuner kit from Team Beefcake that has the 3.6 inch pulley installed along with the Stage 2 intercooler. Also installed is the Reische 170 degree thermostat and Brisk 1 range cooler plugs. I have had several logs reviews with...
As I have seen other post, I trimmed the 90 degree hose coming off the head unit itself a little too much and now it wont fit. I was able to find an intake hose at the local auto part store that almost looks like a dryer hose to at least get the car started. Everything seems fine but I obviously...
Have a GT350 manifold installed. Vacuum lines are routed as many others in the forum have done as shown below:
I reviewed the ProCharger documentation and can't quiet figure out how to route the new hoses. Would it make sense to just remove the hose with the quick release fitting going to...
Starting install of Paxton setup and had a few questions....
Torque spec for pulley bolt? How hard was stock pulley to pull off?
Torque spec for bolts that hold bracket to Timing Cover / Block.... Instructions say to just "Secure" them. I assume the factory torque for those bolts will...
So after going to several companies for quotes on a blower setup, I ended up going with the Paxton Beefcake Special. I have to give a shout out to Terry Reeves who responded to my messages at 10:30 PM on a Sunday night!
I CAN'T WAIT!
beefcake special paxton 15
Head Unit : 2200SL Self...