Hello again. I got a small dent in the lower passenger side door panel that straddles the raised area. I had a mobile dent removal guy come out, and he was able to remove most of it. He said he couldn't remove the remaining portion due to its location. It isn't big enough to pay big bucks to a...
2017 GT. Before I start the car, the battery voltage on the car's gauge reads less than 11V. It is a bit sluggish to start, but it does start. After starting, the gauge reads around 14V. Could my battery be going dead after only three years? It seems like a short battery life. Thanks.
Is there any reason to take the car to a dealer for the 10,000 mile service? They always have a long line, and it can take several hours for simple things, so I'd like to take it somewhere else.
When beginning a trip and after entering a POI, the voice announces the usual "obey all traffic laws, yada yada", but there are no further announcements. I checked settings, and it is set correctly. Where do I go from here?
Thanks.
I received the trunk lid closure strap kit that was advertised last week, but there are no instructions with it. I can't seem to find the thread, but I remember instructions being posted with the ad. I would appreciate if the poster could send me the instructions. Otherwise, I hope it is...
Has anyone had success having a dealer fix the cylinder 8 and random misfire codes? I don't notice any other symptoms, but I had the check engine light come on and then I reset and it came on again in a few days. So something is wrong.
I've recently been having difficulty shifting from 1st to 2nd gear. I noticed this a long time ago, but it was rare, so I didn't worry about it. However it is now happening more frequently (almost every time I drive it). I know the dealer won't take any action unless they can replicate it while...
I've owned my MGW for about a year. Unfortunately, I'm starting to develop arthritis in my shoulder, which makes it painful to get into reverse, and I know it is only going to get worse. I really like the MGW, but I need to look for a new shifter that uses a pull-up collar instead of push down...
Why does the Ford replacement clutch line have the rigid section along with a braided section? All other aftermarket lines are a single braided section. It seems like braided lines would be easier to route.
I tried my new water softener today. It worked really well, as I didn't notice any mineral spots after drying. The last time I washed it there were numerous spots on the car that I had to remove with detailing spray. I'm very happy with the product and will continue using it...
I had my speed shop change my tranny fluid to BG Synchroshift II along with BG additive. I already had a MGW Race Spec shifter and a Steeda clutch return spring installed some time ago. There were two issues I wanted to eliminate: 1) There was a pronounced, annoying grinding/raspy noise heard...
I'm still getting a grinding noise in the shifter area when the engine is cold. It eventually goes away as the engine warms up. I have a MGW shifter installed, but I don't think there's any problem with it. It must be something else. Any ideas?
I finally got a chance to take the car out in the sun for a while today and get some photos of the paint defects of the front bumper. Does anyone know what I might use to remove them or am I stuck? I've tried clay, waterless detail spray, and polish to no avail. They are almost invisible in the...
I can't bring myself to pay $70 for a color-matched plastic grill pony. Is there a good way to change the color of the stock one? I was thinking something like Plasti-Dip, but that may not stick well enough.
I'm applying a decal to the windshield, and I've followed all the instructions to the letter, but after two hours, I still cannot remove the plastic backing without also un-sticking the letters. Should I just try again tomorrow after the wetting solution completely dries?
The tuner who did my PP2 install gave me a call this morning. He told me not to hold my breath for a new calibration from Ford, but that he can fix the cold rev hang issue. So I'll be dropping by there soon to have it done. Fingers crossed, but he seems to have a great deal of expertise in tuning.
I bought a banner decal for the upper portion of the windshield, and I'm wondering whether it will cover any sensors and cause problems with the electronics. Does it need to be positioned a certain way to keep sensors clear? Thanks.