Search results

I am having annoying vibration with the car, It is a 6r80 with a DSS Aluminum one piece, I just realized the markings on the adapter and the driveshaft were off, I fixed it and the vibration was still there, (NOT AS BAD but they were still there) the question I have is when rotating them, are we...

i am having an issue with my car shutting off, i have started to narrow down the problem which it involves my brakes/braking. I am not 100% sure how a brake booster works but based off things I am reading this is causing issues to my car attempting to shut off while i press the brakes. My vacuum...

Dumb question, am on a Gen 2 car, it was previously a Gen2 short block and is now a Gen 3 short block with Gen 2 heads, anyone that is experienced that can Chime in and let me know if it is the 10qts, or the 8? I'm leaning towards 10 but not 100%, ill still be checking oil level with indicator...

Had an accident when removing my motor about 2 years ago , the Crankshaft Position Sensor wires ripped, I already fixed the green and yellow wire. There is a 3rd exposed wire which not sure where it leads. Anyone know how to go about that wire? The picture shows the silver wire which is the...

Any other valves available other than Ferrea For built motors? I am having a motor built by RPG and I want to get better valves than stock but I have ordered Ferrea from different sites twice now, one a couple months ago which advised me that they don't have them available and refunded me...

so i have a Crank hub for an ATI that does not want to come out for anything. I have used a 3 jaw puller and a torch plus a combination of a sliding hammer with the 3 jaw puller. I honestly just want this thing out asap , i need the other components inside but any tips on removing this junk? i...

Having issues removing engine.. i have removed basically everything including the top transmission bolts the 2 on driver side and 2 on passenger side.. i tried lifting it however only driver side seems to go up. Is there any other bolts i may be missing besides those that the transmission might...

Well I am ready to get a sleeved motor started and i already spoke with some larger name shops to get it done. It is just the shortblock. Regarding heads, I have read that leaving them stock is perfectly fine, now my question is what did you pair them with? Valves and springs? as well as any...

What is the easiest way you read boost? I have an AEM boost gauge but it's just not helpful, it goes in increments of 2 and when I'm pushing decent amount of power its just not safe looking at the gauge. Any easier ways that something can record my boost? also should a dyno session allow it to...

I'm on a stage 2 P1X with ATI crank pulley standard crank size 15/17 with the tensioner that does not have the rod on the opposite side. I am running a 3.85 now and i want a tight fit, i had a K080660 on a 4.13 which could have been a little tighter, should i go to K080657 or K080653? Also i...

2015 Ford mustang GT Premium 6r80 42.6k miles $34k, have turned down 32k. clean title, title in hand Procharger P1X Procharger Big red BOV ATI crank pulley Stainless works LTH Catless headers Fore Dual pump level 3 fuel system ID1050x Injectors Driveshaft Shop driveshaft Driveshaft Shop...

I'm literally getting ready to meet a buyer and my car's AC decides to not want to be a part of it. I know EVAP is an known issue. My compressor clutch turns on, problem is i get NO AIR, like nothing at all.. all i can find is people with issues that they get hot air, well i don't even get any...

8 rib 4.13 pulley. 70$ shipped

Procharger proflow BOV with the required tube, basically "plug and play" not sure what it can go for but 150$ shipped. For anyone that just wants a quiet BOV

I just installed a PC red race BOV, lets say installation is a PITA, however, i had the PROFLOW BOV is the RED RACE meant to be open? i turned the car on and it doesnt close during idle?

Upr catch can, comes with another smaller hose, used with IMRC delete and ran the line through the back of the motor. Mount is also available just need to locate it, will add pictures once i look in my parts box. 140$ shipped

Well Im building my block very soon and i want to do the p1x maxed out with a nitrous shot and once im ready for the F1 i'll do that purchase, anyone have experience with this?

Anyone do exhaust dumps? I want to cut my diffuser and just do straight dumps to save some weight.. where do you get them? Exhaust shop & performance wise does it affect anything? I have corsas and can sell them for good $$ and use the money to get closer to a sleeved block but if power...

My car is currently leaking at the moment. I haven't used it in a week and i made some changes (small changes) before tx2k. I turned car on and it smelled like burnt. passenger side valve cover seems to be the issue, i found the bolt closest to the bumper to be loose, is it okay to just tighten...

I have a 4.38 pulley no bends and is solid, used for about 300 miles before went smaller $65.00 shipped. Blow off Valve Procharger dont have to sell but its a hassle for me to change it out due to having to get it welded etc. $250.00 shipped