Search results

I believe because of the 'lip' or flange on the vent you will have to snap it in from the outside. I think there are plastic clips that will engage to hold it in place.

Maybe this pic will help. I took it when I was dynamatting my trunk. I believe that vent will have to be pressed in from the outside of the trunk. For orientation - the "black squiggles" in the upper left corner are on the inner fender well.

A couple of thoughts - 1. If you can lockup tires on dry pavement, then better or wider tires. [sounds like you already covered this] 2. If you are looking for better general bite in a daily driver then a street pad. [I had good results on my supercharged F150 with Hawk street pads] 3. If you...

Mine has that sticker too. A/S Zero Neros in 19" size.

Here's another data point for you from my GT non-PP with 50th package: Before: Fr: 28-3/8", Rr: 28-5/8" Immediate After: Steeda progressive Fr: 27-0", Rr: 27-5/8" After settling [3 months later]: Fr 27-0", Rr: 27-1/8"

The funnel is in the trunk. You'll need it if you ate Taco Bell. :headbonk:

Those images were hard to see. I agree that 85-90 mph seems low for a race. We are all assuming that the guy that was arrested on the scene was telling the whole truth. If I was responsible for participating in a race that killed innocents, I'd be likely to want to lie about my true speed...

There is no 'Bible' for this sort of thing, so you will get 100 slightly different answers. I put the most weight in the following two axioms: 1. No red line runs in first 400 miles. 2. Engine load needs to be varied regularly in first 400 miles to seat the piston rings or you risk having an...

New tires mounted? Seems like every time I get new tires the wheel jockey over inflates them.

I had an image of you going narcoleptic :D

Enjoy! Be careful, that smile may become permanent.

I have the full cat back and had to work on the drone. Sixth gear was bad. I dynamatted the trunk, spare tire well, and inside fenders. I then layered Home Depot denim insulation across all of the inside surfaces. One additional layer under the trunk mat and I am now a happy camper. It took...

Not sure where their customer service is based out of. It's possible that they are in one of the Eastern states affected by the snow/ice storms. ...or maybe India had a cyclone? :D

I have a non PP car and did not like the cornering either. Too much compliance and floaty-ness when cornering. Start with adding a strut tower brace, k-member brace, and the rear IRS braces. It made much difference in my car. I later added progressive springs, and larger sways. That...

I drained my halogen blinker fluid for weight reduction and swapped my muffler bearings to low friction ceramic. Mullet jockeys better look out!

Did you notice if it felt this way stock? Mine had a sway or compliance when cornering medium aggressive. After adding the Steeda IRS braces the rubber band feeling is basically gone.

You guys ease up on the OP. He's now got a better appreciation of how quickly things can go south, and no one was hurt. I've had my car for four months longer than the OP and am still getting to know the limits of the car. I've been surprised on dry pavement with my 19" A/S in 39* dry...

I have done sound deadening. I used dynamat extreme and covered the trunk floor, spare tire well, inside quarter panels and inside fender wells. I considered using a rubber sound barrier, but cheaped out and used the Home Depot cotton insulation. Overall cost was about $160 in materials. The...

A coworker had a high mileage Jaguar in for service. They "inspected" the vehicle and handed him a three page estimate of what was "wrong" with the car. It totaled more than $14,000. It had things such as replacement of axles, control arms, and other major components. He just walked away...

Those should be some of the easiest tires to spin. I have similar, but in the 19" from the 50th-AP. The other day it was 38* and I wasn't trying to break them loose, but 75% throttle in 2nd gear was all it took (3.55 gear). The rear end did a little left-right-left jitterbug with the traction...