1/4 Mile Fast List 3.0

[rabid_josh]

Finally got to try out my new additions on my 2020 401A GT PP1 car.

its tuned on e85, JLT Cold Air, Ultimate Headers 1-7/8s long tubes, BMR Cradle lockouts, BMR vertical links, VMS Racing wheels, 305/45R17 ET Street R.

as noted in the image:
75 degress
32% Humidity
2318ft DA

60ft- 1.777
330- 4.970
1/8- 7.569
1/8 mph- 94.81
1000ft- 9.800
1/4- 11.685
1/4mph 119.51


and a marginal track surface. Ive 60ft better last season, but we make more hp/tq than last season.

Sponsored

 

[Spykexx]

Finally got to take the car out.

2020 GT Premium
Full Weight (No scale there)
Lund E85
SW LTH
Indy Firehawk 500 tires
Drag Mode

DA: 3050
Car: 602(right)

60ft- 1.903
330- 5.162
1/8- 7.773
1/8 mph- 94.74
1000ft- 10.003
1/4- 11.886
1/4mph 120.01

 

[rabid_josh]

Finally got to take the car out.

2020 GT Premium
Full Weight (No scale there)
Lund E85
SW LTH
Indy Firehawk 500 tires
Drag Mode

DA: 3050
Car: 602(right)

60ft- 1.903
330- 5.162
1/8- 7.773
1/8 mph- 94.74
1000ft- 10.003
1/4- 11.886
1/4mph 120.01

not a bad pass at all especially with the DA. With a DA correction calculator youre like 11.45@124 .. granted those arent always accurate, still a great pass none the less

 

[Spykexx]

not a bad pass at all especially with the DA. With a DA correction calculator youre like 11.45@124 .. granted those arent always accurate, still a great pass none the less

Thanks! Was my first time ever on a track. A lot of 12.0's as I was battling traction issues pretty badly, off the line and solid quarter second slips on the 1-2. Need to get off a street tire

 

[MKL_DS]

Thanks! Was my first time ever on a track. A lot of 12.0's as I was battling traction issues pretty badly, off the line and solid quarter second slips on the 1-2. Need to get off a street tire

I was consistently faster in track mode vs drag mode on the MPS4s.
Spinning on the first 4 shifts does not help with good ETs.

 

[Rjames18]

Can we update my time?
Link below has time slip in the video. On my work computer so cant download any outside pictures on here.

 

[Spykexx]

I was consistently faster in track mode vs drag mode on the MPS4s.
Spinning on the first 4 shifts does not help with good ETs.

Myself and another firehawk guy tried to run with track, and posted much slower times. I think my fastest in track was 12.5, meanwhile even with the spin I was pulling 11 seconds in drag.

 

[cahouston]

Can we update my time?
Link below has time slip in the video. On my work computer so cant download any outside pictures on here.

Updated what I could see from the slip in the video. When possible, can you share your 60' and 1/8 ET/MPH?

Awesome time btw! Beautiful build!

 

[Fx2beast]

2019 Mustang:
roush 2650 blower (stock pulley)
Killer chiller (drag unit)
Stainless power longtube headers (catless)
Steeda h pipe
Flowmaster outlaw axle back
JMS boost a pump
Wengerd Performance 93 tune
VMS drag setup with MT Street rs
Done at Alamo City Motorplex
Weight 4000
DA 1800

 

[MIKE MOORE]

Well a year later I get to move up the list a little. The car is almost the same as last year, but I put the stock converter back in, went to a 72mm pulley, E85 and tuned by Wengerd Performance. Left lane of course lol. DA was 3150 on this pass.

 

[Fx2beast]

Someone gonna update this.or nah???

 

[cahouston]

Someone gonna update this.or nah???

Updated. Sorry for the delay. I got busy right after the last update and lost track of the thread.

I may have missed it but what trans and rear gear ratio do you have. Nice times man!

 

[MIKE MOORE]

Another new personal best, took a little weight out, and added a vmp 163r mono blade. Car without me is 3627 and with me is 3842. This run was at 3651 DA. Right lane car 56 of course.

 

[cahouston]

Another new personal best, took a little weight out, and added a vmp 163r mono blade. Car without me is 3627 and with me is 3842. This run was at 3651 DA. Right lane car 56 of course.

Updated. That was a serious improvement with the mono blade and weight reduction considering worse DA! Nice work!

 

[MIKE MOORE]

Updated. That was a serious improvement with the mono blade and weight reduction considering worse DA! Nice work!

Thank you! I'm hoping to crack the 8.99 barrier this fall and really move up the list. I've got about 100 more pounds coming out when my welder gets me in to make the aluminum exhaust and the Anderson composites stuff gets here, and I've got a 69mm griptec that the guys at VMP hooked me up with just patiently waiting lol!

Sponsored