Anyone on Koya wheels yet?

[Melbnut]

Have a look at SF06, it might not be as concave?

I think i will stick with the sf04. I am sure they can work it out. Even if they need to take the car in and do measurements. As i said before the guys from Koya and the shop have been nothing but helpful so far. Its just me being annoyed that i cant go and enjoy it

so close yet so damn far

Sponsored

 

[Yeah Nah]

Melbnut is this classified as illegal? IMO it looks fine.

The Corsa tip can do with straightening up.

 

[Melbnut]

Melbnut is this classified as illegal? IMO it looks fine.

The Corsa tip can do with straightening up.

I think the rear look is better than looking straight down over the car. I think the drop will def clean it up a little.

Hah! the corsa is lined up well.. Have they been done wrong? the actual writing is off centre

 

[Yeah Nah]

I think the rear look is better than looking straight down over the car. I think the drop will def clean it up a little.

Hah! the corsa is lined up well.. Have they been done wrong? the actual writing is off centre

Nothing to stress about. The drop will compensate plus the arch on the rear bumper accentuates it sticking out. I love it. Gives it a ballsy looks.

Didn't know the writing was off centre on the Borla.

 

[Melbnut]

Nothing to stress about. The drop will compensate plus the arch on the rear bumper accentuates it sticking out. I love it. Gives it a ballsy looks.

Didn't know the writing was off centre on the Borla.

Maybe.. its definitlay poke. I will let them sort it out during the week. But it will get dropped on thursday so hopefully it can tuck them up further. But i just cant see that happening with the amount they stick out.

Maybe they can pull it off if they push the offset to the max of 45? no idea tbh

Ohwell the wheels themselves look amazing and the finish is great. Just need to make it work (and find some black lock nuts! suggestions?)

 

[Burkey]

Maybe.. its definitlay poke. I will let them sort it out during the week. But it will get dropped on thursday so hopefully it can tuck them up further. But i just cant see that happening with the amount they stick out.

Maybe they can pull it off if they push the offset to the max of 45? no idea tbh

Ohwell the wheels themselves look amazing and the finish is great. Just need to make it work (and find some black lock nuts! suggestions?)

Do you know the taper and seat depth?

 

[Melbnut]

Do you know the taper and seat depth?

Nope. That is far to technical for me

 

[Yeah Nah]

Red Stang 302 here may assist you http://www.mustang6g.com/forums/showthread.php?t=47406&highlight=lock+nuts

 

[Burkey]

Nope. That is far to technical for me

You'll wanna get some specs from Koya then I reckon.

 

[05STNG]

Do you know the taper and seat depth?

Are you referring to the area of the wheel nuts

 

[Burkey]

Are you referring to the area of the wheel nuts

It took me a while...:headbonk::doh::clap2:

 

[Melbnut]

well unfortunately the koya have come off. The offset will not work. The shop is working with Koya but i believe that i will be going a different route with wheels...

DOH.... maybe some tsw... or maybe the fs02 from MMR? no idea.. all in all i am disappointed. But the car has been lowered and now sits correctly

 

[Burkey]

well unfortunately the koya have come off. The offset will not work. The shop is working with Koya but i believe that i will be going a different route with wheels...

DOH.... maybe some tsw... or maybe the fs02 from MMR? no idea.. all in all i am disappointed. But the car has been lowered and now sits correctly

They can't do the required offset?

 

[RSPEC-015]

well unfortunately the koya have come off. The offset will not work. The shop is working with Koya but i believe that i will be going a different route with wheels...

DOH.... maybe some tsw... or maybe the fs02 from MMR? no idea.. all in all i am disappointed. But the car has been lowered and now sits correctly

I'm not surprised but I hope it all gets sorted for you.

With a 10" front, offset has to be around 35 to 40mm. With an 11" rear, offset has to be around 50 to 55mm.

TSW have a Mustang specific fitment but I can't recall offhand what it was.

The FS02 is a new style rotary forged wheel from MMR and looks the goods. Some photos are now turning up in the Wheels & Tyres sub-forum. You could be the first in Australia with that wheel!

 

[Burkey]

The biggest issue I'm seeing with a lot of the local stuff is these bloody 8.5" fronts.
I can't speak for all states, but in VIC you are NOT allowed to run a narrower rim.

Sponsored