Who makes this 18+ Diffuser cover? Cervinis?

[Mustangpursuit]

Either way post your results once you get it and install it and if it has different instructions such as actual bolts as well? the stalker side skirts require bolts yet is advertised same as "easily installs with 3M tape" so perhaps this kit may have more to it than just adhesive, no photos of the parts kit though.

I keep thinking it looks more off if not using the stalker side skirt because it is essentially lowering the valance ground clearance since the stalker side skirt is an add on also lowering the ground clearance and evening out, so if no side skirt is used, the rear will look lower than the center section of the car like some piece is missing.

Sponsored

 

[Mr. Met]

They were delivered today. I'm not sure what I was expecting, but they are bigger and more substantial then I pictured them. They seem very well made. They do come with hardware for the installation so I am not sure why they wouldn't include that on the product page.

Again, I think they will be fine by themselves, but the side skirts can always be added later if they are needed. Also, stock, the back of the Mustang is higher then the side.

 

[Mr. Met]

P.S. There was no 3M tape included

 

[Mustangpursuit]

P.S. There was no 3M tape included

But does it require 3m tape in certain spots?

 

[davidkrocks]

P.S. There was no 3M tape included

be sure to post pictures once it's on. it looks like a great addition!

 

[Mr. Met]

But does it require 3m tape in certain spots?

There is no mention of tape in the parts list, tools, or instructions. Just a Cervinis sticker.

How do the side skirts go on? I see it says it includes hardware but it also mentions tape. They should post the instructions online.

 

[Mr. Met]

be sure to post pictures once it's on. it looks like a great addition!

Will do

 

[Muhnopoly]

They want over 300$ for those 2 pieces ?! Looks good but not for that price point

 

[Mr. Met]

They want over 300$ for those 2 pieces ?! Looks good but not for that price point

Of course I would like everything to be cheaper, but they do cost money to make and ship. It reminds me of when I bought my 2015, one of the first things I wanted was JLT's full length radiator support cover, but unfortunately they no longer sold them. They told me it was because their mold broke and they didn't make enough money off them to have another one made. And they were selling that thin piece of plastic for $300 back in 2017! How many of these are Cervinis going to sell? I dont know, but I cant imagine it will be thousands so I can understand the price.

 

[Mustangpursuit]

I was washing my car and also polishing my Shelby double walled tips and was thinking again about this and realized it would be a lot harder for me to polish and reach in to buff my tips with the bottom plastic now blocking access

 

[larr12]

Love the look of that splitter.

 

[Xtian_Av]

They were delivered today. I'm not sure what I was expecting, but they are bigger and more substantial then I pictured them. They seem very well made. They do come with hardware for the installation so I am not sure why they wouldn't include that on the product page.

Again, I think they will be fine by themselves, but the side skirts can always be added later if they are needed. Also, stock, the back of the Mustang is higher then the side.

Any Pics of them installed? Been looking at these for a while now but haven't pulled the trigger

 

[Mr. Met]

The installation was fairly straight forward, once I figured out exactly what screws I should be taking out. There was one part of the instructions that I couldn't figure out (seems like a hole for a screw is missing) so I have a screw left over. Going to email Cervinis for more information but it seems fine. The only issue I could see is for some reason the right side, where it meets the diffuser, was not flush despite it being fully bolted on. Some double sided tape would fix it but what I had was too thick. I have a small roll of extra thin tape coming from Amazon.

Always thought it looked unfinished with the bottom left open. Had the gt350 diffuser installed on my 2015 but I really like the way this flows with the stock one. One thing I hadn't thought about was if they would work with the RokBlokz. Luckily the fit nicely with them .

 

[Mustangpursuit]

The installation was fairly straight forward, once I figured out exactly what screws I should be taking out. There was one part of the instructions that I couldn't figure out (seems like a hole for a screw is missing) so I have a screw left over. Going to email Cervinis for more information but it seems fine. The only issue I could see is for some reason the right side, where it meets the diffuser, was not flush despite it being fully bolted on. Some double sided tape would fix it but what I had was too thick. I have a small roll of extra thin tape coming from Amazon.

Always thought it looked unfinished with the bottom left open. Had the gt350 diffuser installed on my 2015 but I really like the way this flows with the stock one. One thing I hadn't thought about was if they would work with the RokBlokz. Luckily the fit nicely with them .

Does the outer stock tip touch the plastic, maybe it is the camera angle? Might be a risk for some after market exhausts.

 

[Mr. Met]

Does the outer stock tip touch the plastic, maybe it is the camera angle? Might be a risk for some after market exhausts.

I dont remember it touching during install but I will have to double check. My tips have always been uneven, but at least there evenly uneven.

Sponsored