What did you do to your Mach 1 today

[swoop1156]

Man I pulled that thing out and didn't gain a tenth in the 1/4 mile. Not sure it was worth the effort

I'll never know, I suppose. I still can't drive it legally since I'm waiting on titling and paperwork from one state to another. Figure if I start with mods, I'll never know the difference, nor will the car with all the sensors and crap.

Sponsored

 

[2022 Mach 1]

I'll never know, I suppose. I still can't drive it legally since I'm waiting on titling and paperwork from one state to another (not to mention a damage claim from the shipper). Figure if I start with mods, I'll never know the difference, nor will the car with all the sensors and crap.

Enjoy the car. The 10hp lose is on paper only. I've had the car to the drag strip twice now. Didn't gain a thing. Destroyed plenty of other mustangs. Especially gt-350s

 

[IPOGT]

Tonight I’m cleaning the wax from the Mach 1 emblems. I’m using cotton swabs and a toothpick. I think I may be losing my mind. ….

 

[willymo72]

Enjoy the car. The 10hp lose is on paper only. I've had the car to the drag strip twice now. Didn't gain a thing. Destroyed plenty of other mustangs. Especially gt-350s

Gt350s, really? Remind me are you 10AT? I thought the 350s trap a few mph higher than the machs with similar ETs..

 

[TEAsGrabber]

Front boi-racer splitter removed.....scraping driveway ain't gonna work! LOL. Gurney flap installed.... New tires ordered..... I can wash it tomorrow!!

 

[2022 Mach 1]

Gt350s, really? Remind me are you 10AT? I thought the 350s trap a few mph higher than the machs with similar ETs..

here's the proof

 

[2022 Mach 1]

Gt350s, really? Remind me are you 10AT? I thought the 350s trap a few mph higher than the machs with similar ETs..

Yes a10. Not idea conditions. The a10 woth the new mach 1 calibration is light years ahead of the gt. Revin Evan Smith had gone 11.8xs on a stock car and steeda went 12.09 back to back with less than 40 miles on the car.

 

[willymo72]

Yes a10. Not idea conditions. The a10 woth the new mach 1 calibration is light years ahead of the gt. Revin Evan Smith had gone 11.8xs on a stock car and steeda went 12.09 back to back with less than 40 miles on the car.

Makes sense, I was thinking you were 6mt hence the question. Those are impressive times and so repeatable, gotta love it.

 

[Zelek]

Alright, here are the turn signals. My splitter is off because I'm buying rivet nuts to fix that whole removing the splitter piece where you have to drill them out every time.

@Diode Dynamics Thanks for the resistors. They work perfect and no galloping sound on the dash. I used the yellow wire and black ground wire for reference and used double sided 3M tape on the air duct for the resistor, and the regular GT/GT350 lights for 15-17 fit the Mach 1 perfectly. You need to remove the bumper since the coolers block a lot of easy access.

 

[Woodie]

Steeda jacking rails and h-pipe. The H is awesome.

 

[TEAsGrabber]

Washed her yesterday...... Woke up this am @ 330am....damn DLS! Bored as f*ck.....Hand waxed her twice! Noticed a couple paint flaws....back bumper cover run/sag in the primer in the license plate well. The other is in the passenger door sill. Don't know that I wanna have a dealer touch them or not. The orange peel isn't too bad, but I'm sure it will eventually bug me enough to wet sand the whole car. Winter project when the weather is cold etc.

 

[swoop1156]

Got my 16' CarCapsule ready to put on for the winter. Installed the pigtail for their IntelliCharger and have it hooked up testing it out. All appears well.

Gonna clean up the car, turn it around, and park it. Still sitting at 59.4 miles.

 

[partsbin]

do all the buttons on the gt350 wheel work correctly? and work thru the menu fine?

especially interested about the bottom right buttons setup on the mach 1 vs the gt350?

I do not believe the buttons on there now will work and are meant for the 350 models only. I am swapping over the entire assembly from my current wheel and essentially just using the shell of the 350 wheel.

 

[cerbomark]

installed steeda clutch line under the hood.
Super fast delivery thru USPS!!
What should take 5 mins took 45 mins, very tight working area.
I trust the black hose supplied is made for brake fluid.

FYI, with the force it took to remove the OEM lines they will never fall off, LOL, but they may leak.

 

[swoop1156]

I completed the Diode Dynamics side marker lights and interior LED swap tonight. Didn't have time to do the sequencer or 4th brake light yet.

Sponsored