Procharger squeak sound PLEASE HELP!!!

[BruceStang]

Just be looking over your shoulder. This ain't no old man in a convertible. This is your Procharger's worst nightmare

Shots fired!! That's it I'm pulleying down, getting the transmission beefed up. Remember you're older than me so act your agej

Sponsored

 

[Doctor Fishtail]

Shots fired!! That's it I'm pulleying down, getting the transmission beefed up. Remember you're older than me so act your agej

I don't mean to be mean old man. But remember that ole saying if you F**K with the bull you will get the horns. Well......you F**Ked with this bull and now where is your car. ;) Deadman5 is gonna get you. :lol:

 

[BruceStang]

I don't mean to be mean old man. But remember that ole saying if you F**K with the bull you will get the horns. Well......you F**Ked with this bull and now where is your car. ;) Deadman5 is gonna get you. :lol:

Yep... your words
"I will say this. Bruce car with a 79mm pulley is right there with me. If he goes to a 75mm we would be neck n neck. I hope does not go to a 72mm "

 

[Deadmau5]

Well if he's making 700+ .... Than we all know the outcome... I don't make that kinda power yet

 

[Tommy V]

I do and do it on 93

 

[Doctor Fishtail]

Yep... your words
"I will say this. Bruce car with a 79mm pulley is right there with me. If he goes to a 75mm we would be neck n neck. I hope does not go to a 72mm "

You have to understand that I was trying to make you feel better since that day you got the Horns. I don't like being a bully. So just giving you hope for one day maybe you can give instead of taking.

 

[Deadmau5]

I do and do it on 93

I make right at 676 on pump... With a much smaller blower than you lol. We still have yet to race ! Than I'll have the Mani on I have a feeling I'll get ya

 

[Tommy V]

Yea your car is making good power for what u have done.Still deciding my next move,probably will be full tire and wheel set up for the track.My car should go low tens easy with the power and mph i have,i just have to get it all to the ground.19 in drag radials are not cutting it anymore ,i need slicks for this stick car.

 

[Doctor Fishtail]

I make right at 676 on pump... With a much smaller blower than you lol. We still have yet to race ! Than I'll have the Mani on I have a feeling I'll get ya

That feeling you have. :lol:
:lol::lol:

 

[z06psi]

I do and do it on 93

Me too and I am on 92.

 

[Deadmau5]

Me too and I am on 92.

You never told me how to get those bearings out !!!. I hammered the fuck out of them and they ain't budging

 

[SoCalTim]

You never told me how to get those bearings out !!!. I hammered the fuck out of them and they ain't budging

Using a press is always the best method, however if you don't have access to one then you can just use a socket that fits inside the hole of the pulley and hammer on it to drive out the bearing.

 

[z06psi]

Step 1 take the circlip out.

Step 2 take two pieces of 2x4 and place pulley on top, circlip side facing down with the bearing able to go between the 2x4s.

Step 3 Get a socket the same size as the inside bearing race.

Step 4 knock them through.

I really doubt the outside race seized to the pulley but with enough heat anything is possible but highly doubtful.

 

[z06psi]

Or use a press. Mine knocked out with some force.

 

[Deadmau5]

Step 1 take the circlip out.

Step 2 take two pieces of 2x4 and place pulley on top, circlip side facing down with the bearing able to go between the 2x4s.

Step 3 Get a socket the same size as the inside bearing race.

Step 4 knock them through.

I really doubt the outside race seized to the pulley but with enough heat anything is possible but highly doubtful.

Well don't make me feel stupid ....lol I know how to do all the other I was just stating that shit wasn't budging and I've beat it like it owed me money . Wanted to be sure I could hit it hard enough without damaging anything .

Sponsored