PKAD Presents BC Forged Monoblock and Modular Wheels for the Shelby Platform

[Paul@PKAUTODESIGN]

Introducing the all new BC Forged KLS01 in the flesh !

Can't wait to mount these badboys up.

Sponsored

 

[Paul@PKAUTODESIGN]

Fresh set of BC Forged HCS35 wheels ready to help terrorize the streets.

Contact us for your next set

 

[Paul@PKAUTODESIGN]

Another set ready to go home !

BC Forged KL12 in Matte Black finish

 

[Paul@PKAUTODESIGN]

Another fresh set ready to go !

BC Forged HCS21S

Brushed dark black center
gloss black lip and inner barrel
Visible hardware

Contact us for your set today.

 

[Paul@PKAUTODESIGN]

A little throw back to our personal set of BC Forged EH181 Wheels with all the good features added !

 

[5.2 liters of democracy]

Personally, I can't say enough about Paul and his crew. I went there to have my new wheels installed (below) and needsless to say, I couldn't be happier with the service and the result. If you need a shop owner you can absolutely trust, Paul is your guy.

 

[Paul@PKAUTODESIGN]

Sorry for the late response its been a busy week at the shop with builds and small jobs here and there.

Thank you very much for the opportunity and letting us get you these super badass wheels they came out amazing.

I really think this will be my next set for my future Mustang, just not gatta figure out which Stang to get.

 

[Orcagt]

Personally, I can't say enough about Paul and his crew. I went there to have my new wheels installed (below) and needsless to say, I couldn't be happier with the service and the result. If you need a shop owner you can absolutely trust, Paul is your guy.

i was hoping to see these on a 350. Did you go with R spec spacing? Can you cake some more photo from a little farther away.

 

[5.2 liters of democracy]

i was hoping to see these on a 350. Did you go with R spec spacing? Can you cake some more photo from a little farther away.

I can take some this weekend with a higher-res camera. I did 19x11 ET50 all around with a 25mm spacer and new ARP studs in front. I wanted a square setup since this car will see a lot of track time.

 

[Orcagt]

I can take some this weekend with a higher-res camera. I did 19x11 ET50 all around with a 25mm spacer and new ARP studs in front. I wanted a square setup since this car will see a lot of track time.

Thanks man. For what your planning its a great set up. I'm thinking 11" front with ET25 and 11.5" rear with ET55. I assume I'd get more concave in the rear and front??

 

[Paul@PKAUTODESIGN]

Thanks man. For what your planning its a great set up. I'm thinking 11" front with ET25 and 11.5" rear with ET55. I assume I'd get more concave in the rear and front??

Same concave actually

 

[5.2 liters of democracy]

i was hoping to see these on a 350. Did you go with R spec spacing? Can you cake some more photo from a little farther away.

I took a few more with my phone in case I don't get a chance to take some further away with an actual camera this weekend. If I do, expect them Sunday afternoon/evening.
Edit: These are on cup 2's. I have the Ford Performance springs sitting in the garage to install which will make it look much better.

 

[Paul@PKAUTODESIGN]

This isnt no April Fools joke !

Got these badboys done and ready and to their home.

BC Forged HCA210 Wheels

 

[Paul@PKAUTODESIGN]

Freshly done BC Forged RZ05 Wheels in Brushed Dark Black Finish

 

[Paul@PKAUTODESIGN]

Pretty unique set of wheels ready to go home.

https://pkautodesign.com/shop/bc-forged-hca381/ on Diamond cut matte gunmetal finish

Sponsored