Sponsored

Carbon Fiber Driveshaft coming soon!

Driveshaft Shop

Active Member
Joined
Jan 7, 2015
Threads
0
Messages
31
Reaction score
18
Location
charlotte
Vehicle(s)
1931 Ford
We will still need to do more testing but 1399.99 is the target
Sponsored

 

Epiphany

Well-Known Member
Joined
Oct 11, 2015
Threads
70
Messages
7,511
Reaction score
11,838
Location
Global
Vehicle(s)
I like to disassemble things.
What diameter is the shaft?

And can you comment on the type as well as the rated strength of the epoxy used to bond the ends to the shaft?
 

Driveshaft Shop

Active Member
Joined
Jan 7, 2015
Threads
0
Messages
31
Reaction score
18
Location
charlotte
Vehicle(s)
1931 Ford
The shaft is 3.8" and a special wind or Modulus

maybe this will also help on what we do, its an older post but the info is good



Our Carbon Fiber Shafts are a bit different, due to the fact that we have decided to take our time and offer what we feel is the best shaft that we could make. Before we come out with a new product we will take the time to investigate, research and put our own spin on what's currently being done. Over the years we have done extensive research, always reading and collecting information about Carbon Fiber, but with all that was going on the time was never right, until now. This company was founded by my father Robert Rehak, along with my uncle Carl Weisane, back in the late 60's when a double cardan CV was considered "High Tech". I would think these gentleman would be rolling over in their graves by now, knowing that we were literally "gluing shafts together".


Over the years I have seen many failures of Carbon Fiber shafts and I have collected many samples, (too many to show) but there was one thing that stood out on all of them. A certain profile on the aluminum (or steel) part that was mated to the Carbon Fiber seemed to be very consistently showing up. When we decided to move forward with Carbon Fiber shafts last year, we wanted to wait until we had our custom balancer in place so we could accurately test the claims of what Carbon Fiber shafts had to offer.

The first thing to do was find suppliers for the tubing, glue and of course the u-joint ends (unless we were going to be making them). I contacted my friends Tony and Brian at Sonnax, whom I've worked together with over the years on several aluminum yoke designs, and asked how their new line of u-joint ends were coming for use with Carbon Fiber. In the past we had been using another manufacturer for aluminum ends and had trouble with more than our share of bad parts, namely some of the GTO 200mph shaft ends that had issues with the u-joint fitment. Sonnax has been supplying our ends for the weld together shafts for quite some time, and their quality was more in line with what DSS demands for our customers, so it was a natural choice to incorporate them in our Carbon Fiber line.



I then contacted our Carbon Fiber tube manufacturer and spoke in depth with the head engineer about critical speed, strength and run out. I found that the critical speeds that they were quoting to us were phenomenal, but after research of our own found some of it to be misleading. They were quoting the tube only and not taking into consideration the u-joint ends and mounting points, like the SAE standards for critical speed show. Still, they were much higher and offered some real benefits to a lot of the newer cars that we were having certain issues with. After this we spoke to the 3M engineers about different glues and bonding processes and moved on to putting it all together.


Back to the design, we were told by the tubing manufacturer that ends of the tube come un-machined (we had known this from the past) and it was up to us to put the profile on the outer diameter of the tube so that the glue would bond correctly. It was suggested that we put a thread pattern, or as we were told, lines like an old 33LP record (you do remember records right?) was the best way to get the correct bond. Now at this point is where DSS deviates from the rest of the crowd, as this is the very same profile that i had seen in every bond failure and was uncomfortable with this assessment of the correct way to bond.






Tony and Brian from Sonnax had said they were working on a new profile for the u-joint ends and sent over some prints for me to look at (which was very cool of them). I was thoroughly impressed, even my gut instinct was happy, so we decided on this design and moved onto the rest of the planning. One very interesting thing that I observed when inspecting various cut and broken bonded ends from the samples I had been collecting, was one of the ends we had cut apart from a current production Nissan 350Z. Take a look at the way the Nissan factory did their bonding. There are no ridges on this one and we couldn't get the tube off of the end at all. It was now a part of the end, and there was no taking it off period. Although the Sonnax design is not exactly the same, it has some very important similarities that made me feel better about our choice.






Glue and Curing. We could go on and on about how much time we have spent on this part of the equation, but I feel some things need to be kept inside of the magicians hat, so all we will say is that there are several ways to bond and cure the glue. We did not take the easy way out on this one. My son Frank IV will be graduating from college this year with a degree in Machine Engineering, and like me he has a real eye for details. I'm proud to say that between him and myself we perfected our bonding process. He will be bonding all of the Carbon Fiber shafts, and of course Matt, our head builder who moved down from NY with the company, will oversee every operation and balance them upon completion. Frankie's no stranger to the shop or cars as he has always been around as a kid growing up. Check out his High School senior project (you should have seen the principal's reaction to him asking about doing this for his senior project). It would hard for me to say he didn't get any help from the guys in the machine shop doing this, but i will say it was all his idea and execution.





So after all of this, we have researched, spoken about and done, it was time for testing. We assembled a few shafts and off they went to the destructive testing lab for some bench testing before we put the shaft in a real car. We prefer this method of new part testing first to make sure all processes are done correctly, with both shafts and axles. Testing went very well, in fact better than we could have hoped for. As you see in the picture below what actually broke was the u-joint cross, the tube and bond remaining fully intact. The torque spec for the u-joint was at about 2600 ft-lbs of torque, but all the test shafts broke right at 3100 ft-lbs (Neapco should be very proud of the performance of these u-joints).





On the Mustang you need to have some sort of slider in the shaft. After several attempts to use a traditional slip yoke and spline had failed, a CV joint was chosen for its movement ability, more so for its ability to move in and out with out any side to side play. We wanted to keep the shaft lightweight but more importantly, come up with a design that would be able to move this heavy muscle car down the track without any issues. I came up with an idea to put a 300M spline in to an aluminum part and engaging it with splines. Some engineering calculations were done and some prototypes were made, and the end result is the shaft shown below. We didn't just stop there though, we also went into the CV and added the DSS 4340 cage and a specially formulated grease that we use for all of our World Challenge and SCCA pro race car axles to make sure there is no issue down the road. This, along with balancing the shaft with all of the fixtures on the balancer, makes every Carbon Fiber shaft that we offer a step above the rest. And if you need a custom shaft made from Carbon Fiber, just give us a call. We're all set up and ready to go...

 
Last edited:

Voodooo

Banned
Banned
Banned
Joined
Nov 2, 2015
Threads
107
Messages
5,822
Reaction score
2,395
Location
SE Michigan
First Name
Scott
Vehicle(s)
Carroll Shelbys Soul Lives Under My GT350 Hood
I'm getting one. When can I purchase one for the GT350?


Sent from my iPhone using Tapatalk
 

Sponsored

Driveshaft Shop

Active Member
Joined
Jan 7, 2015
Threads
0
Messages
31
Reaction score
18
Location
charlotte
Vehicle(s)
1931 Ford
I'm getting one. When can I purchase one for the GT350?


Sent from my iPhone using Tapatalk

We will more than likely release 10 in the next 2 weeks for more testing.
 

Voodooo

Banned
Banned
Banned
Joined
Nov 2, 2015
Threads
107
Messages
5,822
Reaction score
2,395
Location
SE Michigan
First Name
Scott
Vehicle(s)
Carroll Shelbys Soul Lives Under My GT350 Hood

Voodooo

Banned
Banned
Banned
Joined
Nov 2, 2015
Threads
107
Messages
5,822
Reaction score
2,395
Location
SE Michigan
First Name
Scott
Vehicle(s)
Carroll Shelbys Soul Lives Under My GT350 Hood

Sponsored
OP
OP
SVTDSM

SVTDSM

@Serpent_Stangs
Joined
Nov 25, 2013
Threads
26
Messages
895
Reaction score
521
Location
Nashville area
Vehicle(s)
2017 Shelby GT350R
Update

Ive done two track days, and put about 500 miles on the car since installing the driveshaft. No additional vibration, and nothing has rattled lose. Probably did over 350 miles on track, so I'm sure any issues would have become apparent by now.

Thanks again to The Driveshaft Shop for making a top notch part for a top notch car!

Here is one lap from this Sunday.
[ame]
 

DrumReaper

Well-Known Member
Joined
May 17, 2015
Threads
114
Messages
4,985
Reaction score
3,706
Location
South East
Vehicle(s)
1971 429CJ Mach 1, 2012 Boss 302
[MENTION=13271]Driveshaft Shop[/MENTION], I've got an R if you need to test it on that platform... ;)
 

Voodooo

Banned
Banned
Banned
Joined
Nov 2, 2015
Threads
107
Messages
5,822
Reaction score
2,395
Location
SE Michigan
First Name
Scott
Vehicle(s)
Carroll Shelbys Soul Lives Under My GT350 Hood
Are these available for sale yet?
Sponsored

 
 




Top