Search results

Hey Guys I am looking for some advice. I found that the IMRC Rod has failed and now the flaps in the manifold are stuck halfway closed/open. I am looking to replace the manifold. The biggest thing i am trying to avoid is a tune which I've seen most replacements require one. I've been told that a...

I recently discovered that my IMRC shaft has snapped, and I am looking to replace the manifold. I have found that 2018 manifolds are more ready-available. Could anyone tell if any modifications would be needed to swap manifolds?

Hello Guys, I have a 2016 ford mustang gt with a Ford Performance OIl Separator installed and i recently installed a Roush CAI and i noticed that on the left side of the CAI intake tube the vacuum nipple is straight were on the OEM intake tube the nipple is a 90 degree inlet. So when i attempt...

I've noticed that there is a gap between the bushing and the sway bar's lip to keep it center i believe. Any ideas how this could have occurred ?

Does anyone know how to replace these two bolts and where to find the replacement ?

https://ibb.co/D84fP9J I am looking to replace the back two bolts i believe they are 10M X 1.50 i accidentally stripped the bolts. I am trying to figure out how i replace it and where i would find the replacement bolt.

I recently been having issues with my A/C. It started with the A/C only blowing warm air out of all the vents after the car was warmed up. In the mornings i would be able to run the a/c for a little bit (but then i would turn it off and just drive with the windows down). A few days later i...

Thinking i might need to replace my A/C Compressor. Before i purchased the Compressor it self, i was wondering what other parts i might need or should replace while i am doing this work?

Does anyone know where i can get or download a service manual for a 2016 ford mustang gt manual. I attempted to get a PDF one and paid for it but it was a fake i just need a good source.

Hello, I my knowledge on suspension and overall cars is limited so i am wondering any recommendations for suspension upgrades for a lowered mustang on Eibach Pro-Lowering Kit w/ Eibach's Front and Rear sway bars. The wheels are 20X10 275/35/20 MPS4S. Any suspension upgrades that would make this...

I am new to the forum and was wondering if anyone had a link to the rules of the market place for selling an item.

Hello, I am looking for some recommendations on a clutch and fly wheel replacement for a daily driver that is looking to get performance out of a replacement but not to be tracked

I own a 2016 GT manual and i have noticed that in the last few weeks a noticeable grinding or whining sound is coming somewhere in the front end when i am in gear and accelerating. It doesn't do it when i have the clutch disengaged and rev. It only does it when i am accelerating in 1st,2nd and...

Hello, I've been looking for some 5mm spacers for a setup and i was having a hard time finding them. I found some through CJpony but my shipment has been on back order for about a month and i need to get them before my tires come in. I was wondering if...

I am looking to get the SVE S350 20x10 from LMR. I was wondering if anyone had some suggestions on tire sizes they run or have ran. Pictures would be much appreciated

Anyone running a 20X10 SVE S350, Square setup? if so what are tires are you running and what is your feed back on your setup? are you running lowering springs or did you need any additional parts to fit the wheels and tire setup

I was wondering if anyone runs a 275/35/20 on a 20X9 square setup and if you do. Are you having any fitment issues or any issues at all?

any suggestions on some good websites to shop for new wheels.?

Hello, I have been back and fourth digesting so much information on wheels and tires. I was wondering anyone had some solid suggestions on a square setup that won't need any additional parts to run. I wanted to go with a square setup but i wanted to be able to rotate me tires. This car wont be...

Hello, So i am going to be doing an oil change soon and i am completely using a different weight and brand of oil. Is there any extra steps i need to do while swapping from 5w-20 to 5w-30 or can i approach this as a normal oil change. I know that this may be a silly worry but id like to make sure.