Hey guys, I guess I'm getting old but my exhaust is giving me an ear bleed headache if i drive more than 2 hours I'd like some advice in modifying my current Setup:
SW LT headers
Catless OR pipes
x2 Vibrant 18" resonators
Gibson catback exhaust
Its full dual 3" all the way using the original...
Hey Guys,
I was looking for some advice on a parts list. I'm at 75k miles now most of it has been boosted so I'm sure I have some premature wear/failure on some components. If I'm pulling things apart i might as well replace everything that i touch since i'll be tearing pretty much everything...
I've had a Gen5 Whipple for 2 years, roughly 20k miles since boosted about 80k total. Got a P0430 code, cleared it was fine for a few days. Now when doing WOT pull anything above 5500 RPM will throw a misfire code, P0430 came back as well. At first I was thinking bad plug injector maybe sensor...
I've seen this a bunch and unfortunately with no real solution other than to install ugly pins. So if your somewhat handy this works AMAZING! 10x stronger than factory.
Tools Needed:
Drill bits
File
Epoxy (Autozone)
1/2"x1" Aluminum angle (Lowes)
Tin sheers
1 inch Clamps (lowes)
You'll also...
Check out video
[ame]
My car is developing a clicking noise. I did have my Transmission rebuilt under warranty at 6k miles when it self destructed. Now at 30k I'm not sure where its coming from but the engine runs perfectly clutch engages normally no abnormal drivability problems. but its...
Does anyone know the size or if it is possible to replace the stock flasher relay to an electronic relay to get rid of the fault when using switchback LED's? I rather not do resistors and all I had to do is buy a relay for my truck that I did the same mod on. This possible with the new mustang?
So just did an oil change. Filled the new oil filter up and installed put 8 quarts in like my manual specify. Started it and ran it for a minute turned it off let it set for 5-10 min and checked the dip stick.... WAY under the low line.
So i went and got another quart of oil and put half in...
Looking for some advice on what parts I could safely replace by fabbing my own with aluminum. I want to dramatically reduce my weight to around 3300lbs. suggestions on my next project would be helpful.
Parts i've already done:
front and rear crash bars (aluminum)
Hood insulation
sound...
So far I've read a lot of good threads about supporting mods and I don't think anyone has really asked how to add boost but not reduce the reliability or longevity of the engine. Is that even possible or is that just a stupid question? I want to make 700-800hp but not have to sacrifice lifespan...
So pretty sure a syncro decided to dislodge itself in my transmission today. I already dropped it off at the dealer... I drove there parked it in there service department. It still operates normally but just sounds like a screw ticking on a fan blade or your computer or something. so the faster...
I want to run 315x35x20's on the rears and run a little wider that stock on the front. Seemed to push a little bit when I took it to the track when i was taking corners and I want to get rid of that. As far as suspension goes I want to wedge the car slightly so maybe just drop the front end...
Hey guys Just installed a dash cam in my stang today. No ugly cords running down to your cigarette lighter either! Wanted to give you guys some tips on where and how I did it. I know there are some DIY's out for Radar detectors but they have you shoving stuff into your rearview mirror. I...
Update... I beat my 29mpg with a 31.1 with the gauge. Math came in at 30.4. I wish I lived in a flatter area I always hit canyons mountains and 85mph speed limits and it drops pretty dramatically.
My trip to Portland this weekend for valentines day with my wife I got a surprise from my car...
Bought my 2015 PP GT in December and its taken the DMV in Washington till now to finally tell me they cant register it because its not emission's compliant! So i got a little upset and said your crazy they wouldn't sell it to me if I couldn't register it! Well sure enough looked under the hood...