Search results

Hello all, where is the DDM for the 2019 mustang gt premium located at? I called different ford dealers and gave them my VIN and they all said my car has a DDM, I’ve taken the door panel off and never found out?

On paper it definitely looks like a lot but I’m confident if everything is just a plug and play and enabling everything on forscan, then it shouldn’t be that bad, definitely not as time consuming as when I replaced my 2 VVT solenoids on bank 1

Hello all, so ive been doing hours of research on this topic and will be my next "project for my car" and i have many questions regarding the feasibility of this. I have read a few times that 2018+ cars with the 401a package are able to do a plug and play for the heated and vented functions to...

I thought on the 2018+ if you have the 401a, it’s just a plug and play?

Yup! Was the camshaft sensor in the far back that was unplugged, must have forgotten it, plugged it back in, cleared everything once again, fired it up, everything was completely butter smooth, drove it, left for a little, turned it back on; and no CEL came back, nothing pending; and the VCT...

Hello all, a continue on my previous post talking about the intermittent stalling issue, previous diagnosis came to a (hopefully the right) conclusion and replaced VCT solenoid #1(intake) on bank 1, the exhaust solenoid was not necessary to replace but I went ahead and did it anyways because it...

HUGE UPDATE:, the problem has PROBABLY been found as we did a lot of process of eliminations. Had one coworker who still hasn’t looked at it use his high end autel scanner tool, it took him almost a whole hour of diagnosing the issue and has found 2 things but one that may be the leading...

i found these new codes but they’re showing as history as there is still no CEL, there already new 02 sensors in

Oki so during my lunch, I went to the car to start it up, started fine, went to my Bay Area, car started acting up and actually stalled out. Popped the hood and to my surprise the screw for the clamp was perfect, was probably done by the tuner when he said he couldn’t figure it out I used...

huh? i never noticed this at all, it looks like the screw is sitting up against the supercharger preventing the clamp from tightening the hose down properly, but this could cause a car to be doing this stalling on occasion like this?

I thought it required a license to use? the battery is on the newer side, it’s still on a parts warranty so I can possibly exchange it out. It did this before and after the recent custom tune

The only line is that short one going to the actuator right?

1. i have no idea if it was or not, the car came from Cali 2. Id have to diagnose it but the problem is that when it does this, id have to get and i cant dictate when it does. I also dont have IDS, the tuner had it idling for almost an hour and the car never did it but he did see the DTC in the...

Hello all, been having this issue for many months now since i got the car in January but been happening intermittently. Basically any random time once every 1-2 weeks, at low speeds (5mph and under) the car starts this sequence of events and would randomly start to struggle, the revs would...

Hello all, so it’s that time for that new rear tire change, currently on a 305/35r20 Nitto R2 and they’re balding badly and getting close to the wires, car is spinning at almost all speeds, tc kicks in between 70-85 during the 60-130 run. Car ran a 7.8 60-130 on said bald tires with tc kicking...

Hello all, so my car currently is on 93 with the roush 2650 blower, catless headers with a full borla s type exhaust on 670whp. I've been wanting to get an e85 conversion and want to know what to expect with this change, the car is my daily to and from work and want to know more about the...

I installed mine through the air inlet per the instructions, got it in the exact spot. I’ll take a look at the membrane and put the cap back on. So just put a single layer of the making tape over the cap? No gloves or foam? Also I’m not sure but whenever I put the cap back on, idk if it’s seated...

Hello all, recently purchased and installed the foster whine mod for the roush tvs 2650 on the 2018-2023 5.0s. So far I'm not completely happy due to the amount of hissing/air intake noise being extremely audible and overbearing, especially when just cruising and not in boost, tried the 1-3...

did you put the gloves over the cap or just over the tube itself? The whine is a lot better without the cap but the air hissing noise is nearly unbearable

Are you able to still hear the whine?