What did you do to your S550 Mustang today?!

[cerbomark]

Downtown Island?

morristown TN .

Sponsored

 

[cerbomark]

I am trying to look for a way to contact the seller to see if they can do all the red in orange. Do you have contact info or can direct me to ot in the link please?

@skinnyb had the same concern.

JIANGGAI Full Leather Steering Wheel,D-Shaped Flat Bottom Perforated Leather Grip Steering Wheel with Heated Fit for Ford Mustang GT 2018 2019 2020 2021 2022 2023

Looks like the same wheel as mine above.

 

[IPOGT]

@skinnyb had the same concern.

JIANGGAI Full Leather Steering Wheel,D-Shaped Flat Bottom Perforated Leather Grip Steering Wheel with Heated Fit for Ford Mustang GT 2018 2019 2020 2021 2022 2023

Looks like the same wheel as mine above.

I’ve been advised that if you have a warranty, and anything happens related to the steering wheel electronics, apparently it could cause a denial.

 

[cerbomark]

I’ve been advised that if you have a warranty, and anything happens related to the steering wheel electronics, apparently it could cause a denial.

I m past that point, but , save the old wheel and reassemble if you have that big of an issue.

 

[dasrider]

What to you is aimed properly?

Parked car on level surface and use a wall 25ft away for measurements. Measure from center of fog light to ground, then show that on the wall. Aim fog cutoff to be ~2-3" below that measurement. At least that's how I'm going to do it.

 

[Joe Gonsalves]

Well aside from the recent M-9306 kit install, I added the knock off Roush Aero Foils to the rear diffuser. They fit nice and look great. Started my engine bay dress up project. Added a fuse box cover plaque by Pixel Works and a radiator cover plaque by Anchor Room. I have strut tower covers coming soon. And I plan on doing some paint work on the engine cover. I'll post pics when I get it done and when I'm back from travel.

 

[WalkRB8]

Installed one side of the custom Cobra Jet graphics.

 

[Duece McCracken]

Installed the Roush rear spoiler on my Bullitt last night.

 

[Bob Lob Law]

Need to redo the back tint...

 

[Duece McCracken]

Need to redo the back tint...

Lmao, well aware. Its on the list. Previous owner had some BS tint installed by a low bidder. Its way too dark and has not held up well as you can see.

I guess eventually it will just fall off at this rate, rofl!

 

[Stage_3]

Didn't do anything to it, but admire it while in the garage.
But, I did order this for it today,....
(Ahem @Jmeo) LOL

 

[Dan243]

Very Interesting Tail lights! Do you have any pictures with the tail lights on?

I will get a pic with them on

 

[jono12345]

I'm having a bit of trouble finding the best bang for the buck catch can and vacuum block. If anyone has suggestions I'm all ears! Ordered a VMP bap. Going Wengerd tune on GT500 injectors.

The UPR vented catch can is a nice piece and many people run them.

I bought a manifold off Amazon for like $15 and just used some rubber hose to plumb it in. You can see the manifold and catch can in this Pic. Works very well.

 

[Jmeo]

Didn't do anything to it, but admire it while in the garage.
But, I did order this for it today,....
(Ahem @Jmeo) LOL

Oh boy!

 

[geep81]

Slave cylinder died @ 40k miles 2 weeks ago. Got it replaced and while in there replaced a perfectly fine OEM clutch with a McLeod RST. Goes great with the MGW shifter I had put on earlier this year.

Still breaking in the clutch so not launching it hard from a stop, but driving it hard once I'm going and the MGW + new clutch + properly working slave cylinder seems to have cured my MT-82 issues of 3rd gear lockout at high RPM and occasional grinding going into 3rd.

I drove stock shifter/clutch for a little over 5 years, and changing it up recently it feels way better. Hard to describe, cleaner and smoother when making shifts is a good start.

Sponsored