Sponsored
trojannemo
Well-Known Member
Forgot to post yesterday: had the car lowered on Steeda progressives, then had it aligned. Then had it washed, and shortly thereafter had a massive storm ruin the wash.
samd1351
Well-Known Member
- Joined
- Sep 17, 2018
- Threads
- 107
- Messages
- 838
- Reaction score
- 1,489
- Location
- Olathe, KS
- First Name
- Sam
- Vehicle(s)
- 2017 Mustang GT, 1999 Ranger
Men's cologne should be old car smell, wd-40, and smoley burn out!Hang a pine tree freshener on her, she won't smell that way anymore!
samd1351
Well-Known Member
- Joined
- Sep 17, 2018
- Threads
- 107
- Messages
- 838
- Reaction score
- 1,489
- Location
- Olathe, KS
- First Name
- Sam
- Vehicle(s)
- 2017 Mustang GT, 1999 Ranger
Looks very nice! Mine is gone though. Things were getting tight. Had to finish paying for my son's wedding, and it was just time. Besides, it left me enough for mustang. I only really missed it for a minute or two. The new ride ia so much more fun. The old hot rods will always be something special, but the new hot rod is pretty nice too.
Sponsored
GT Pony
Well-Known Member
- Joined
- Mar 13, 2015
- Threads
- 77
- Messages
- 9,402
- Reaction score
- 4,839
- Location
- Pacific NW
- Vehicle(s)
- 2015 GT Premium, Black w/Saddle, 19s, NAV
Finally got around to installing the Steeda Extreme G-Trac Brace I bought quite a while ago. The first one I bought would not mount up because one of the front mounting points was off by about 1/8" ... no way I could get the bolt started - I fought it for an hour.
The replacement brace bolted up perfectly. Kind of a PITA to have to try two braces to get one to mount up correctly. My 2015 has the welded nuts in the frame from the factory (later deleted by Ford), so the two front mounting points on the brace need to be dead nuts on or it won't mount up to the welded nuts in the frame.
The replacement brace bolted up perfectly. Kind of a PITA to have to try two braces to get one to mount up correctly. My 2015 has the welded nuts in the frame from the factory (later deleted by Ford), so the two front mounting points on the brace need to be dead nuts on or it won't mount up to the welded nuts in the frame.
Last edited:
Xavier
Well-Known Member
Put it away for the winter :( It's a little early but the drag strip is closed for the season, there aren't any more car shows to go to till spring and it's been too cold and rainy to really enjoy it.
16Fastback
RMR 8985
- Joined
- Jul 17, 2016
- Threads
- 33
- Messages
- 840
- Reaction score
- 1,377
- Location
- Pennsylvania
- First Name
- Stephen
- Vehicle(s)
- 2016 Fastback , 2009 Ranger 4x4
Same here,but now I have some time to tackle those car show projects I didn't have time for :^)
16Fastback
RMR 8985
- Joined
- Jul 17, 2016
- Threads
- 33
- Messages
- 840
- Reaction score
- 1,377
- Location
- Pennsylvania
- First Name
- Stephen
- Vehicle(s)
- 2016 Fastback , 2009 Ranger 4x4
EvilleGT
Well-Known Member
Put mine away about 2 weeks ago with 6 inches of snow and ice on the ground. Just hooked up the battery tender today. Time to start looking for winter projects to install.
Sponsored
JOKER M1
Well-Known Member
- Joined
- Sep 5, 2017
- Threads
- 56
- Messages
- 1,803
- Reaction score
- 2,140
- Location
- Somewhere in Indiana
- Vehicle(s)
- 2015 GT Premium (SOLD)
Nope but I bet I can order them.Are you close to any OHIO stores?
Xavier
Well-Known Member
Good call. I think I'll look into getting my '18 IM ported and figure out how to run longtubes and still pass inspection up here.
Sponsored