Steeda Irs alignment bushings

[16s550]

Can anyone help me figure out the difference between them? I couldn't really tell. Lol. I also got two of them in on passenger than when went to put driver side in the front went in but back wouldn't fit in whole. Did I just fudge every thing up? Also does anyone have pic of front part that needs to be supported when changing front and rear part of Irs when changing rear.

Sponsored

 

[rvlyssup]

Are you referring to this kit?

http://www.steeda.com/steeda-s550-mustang-irs-subframe-alignment-kit-2015-all-555-4438/

 

[16s550]

Are you referring to this kit?

http://www.steeda.com/steeda-s550-mustang-irs-subframe-alignment-kit-2015-all-555-4438/

Yessir.

 

[rvlyssup]

Other than the slight difference in length of the delrin sleeves, all 4 are the same diameter AFAIK.

The 2 shorter ones go into the front while the slightly longer ones install into the rear of the IRS cradle.

 

[16s550]

Other than the slight difference in length of the delrin sleeves, all 4 are the same diameter AFAIK.

The 2 shorter ones go into the front while the slightly longer ones install into the rear of the IRS cradle.

That's weird so I wonder why the back driver one wouldn't go in. It was like the hole was to small.

 

[rvlyssup]

Did you measure the diameter of all 4 sleeves? Maybe the one that does not fit is over-sized a little...

Even if the cradle wasn't centered yet, the sleeve should still fit right in.

 

[16s550]

Did you measure all 4 sleeves? Maybe the one that does not fit is over-sized a little...

Well I looked at them but when I did they all looked the same and instructions I kinda only got from them that they just have to go facing a certain way but I swear they all looked identical to me.. I left two in lol hope it dosnt cause an issue. In friday taking to shop to see if they can figure it out. I'm not to fond of rolling around on the floor anymore.

 

[rvlyssup]

Yeah I doubt having 3 out of 4 installed will cause any issues.

I have the same kit but only installed the rear sleeves as I have BMR's cradle lockout kit installed up front.

 

[16s550]

Yeah I doubt having 3 out of 4 installed will cause any issues.

I have the same kit but only installed the rear sleeves as I have BMR's cradle lockout kit installed up front.

Ahh i see. Cool thank you. I for sure hope clocking my bushings helps the squeeks I have now. Was hoping it want the sleeves making the noise.

 

[TNcoupe]

Two are a slightly larger diameter than the other two. One of each size goes in one side. Cant remember if the larger one goes in front or back. Its been too long since I installed mine.

 

[Hotpart.com]

I'm not sure about the Steeda ones but they ones we are getting ready to manufacture are different diameters for the front and rear mounts. They are .105" different in size.

 

[16s550]

What I don't get is how was it able to fit three of them but not the 4th one. Neither of the two I had left after installing one side fit. So I left the driver side out. I was to tired to pull the other wide again and they seem to kinda get stuck in there from snug fit.

 

[Niz55]

get a pry bar and align the subframe and insert the 4th one.

 

[16s550]

get a pry bar and align the subframe and insert the 4th one.

Ok I'll try that. So is it safe to say the two I got in on driver side are correct since they slid in and bolted down?

 

[Niz55]

I mean 2 is better than 0. But they are kinda pain in the button to line up.

Sponsored