Steeda's S550 Ultra Lite Chassis Jacking Rails - Now Available

[Todd15Fastback]

Can't wait for mine to get here!!! So stoked at the ability to jack the car easily and also to crush cans!

Steeda Can Crushers!!

I love mine! 10 seconds and the car is about jacked up...

Sponsored

 

[davekro]

I love mine! 10 seconds and the car is about jacked up...

Convertibles are j e a l o u s ! ;)

 

[JolleyRoger]

These have been a great addition while doing springs, exhaust , etc....

it's like that tool you wish you had to make life that much easier, love them!

 

[Cascadia_302]

These are on my short list for sure.

 

[DarkSubRosa]

Installed mine yesterday, so easy to put these things on.

 

[Jonas-RR-GT]

Installed mine today. One thing I notice if you car is lowered on springs. You may have a hard time getting the hydraulic jack under the rail since it sits a little lower. I had to finagle the hydraulic jack to get underneath the rail. Or I could just get some helper ramps that I have seen from Race Ramps.

Other wise very easy to install and I can lift in the middle to rotate my wheels. Great product.

 

[BallisticBurrito]

I got a set of these ordered from LMR sitting in my garage right now awaiting installation. I wanted to get them installed this weekend but laziness and lack of time means I have to wait until next weekend. :/

Though I should say that the box of these from LMR looked like it was sent here after a detour through 1960's Vietnam. Thanks, UPS. :|

 

[plc268]

Installed mine today. One thing I notice if you car is lowered on springs. You may have a hard time getting the hydraulic jack under the rail since it sits a little lower. I had to finagle the hydraulic jack to get underneath the rail. Or I could just get some helper ramps that I have seen from Race Ramps.

Other wise very easy to install and I can lift in the middle to rotate my wheels. Great product.

Curious, what floor jack are you using?

I noticed this myself. I'm not lowered (yet) though, but my low profile jack only has a little bit of space before it touches the rails.

 

[Jonas-RR-GT]

Curious, what floor jack are you using?

I noticed this myself. I'm not lowered (yet) though, but my low profile jack only has a little bit of space before it touches the rails.

I have a Craftsman aluminum 2 ton jack. The lowest is about 3.75"

 

[Cj4428]

Installed my steeda jacking rail today,raised car so all 4 wheels where off ground,put
Jack stands under rail,car was very sturdy,these will make raising car maintance and storing car for winter very easy as I plan on removing tires and storing in basement for our cold
Minnesota winter.

 

[Todd15Fastback]

Installed my steeda jacking rail today,raised car so all 4 wheels where off ground,put
Jack stands under rail,car was very sturdy,these will make raising car maintance and storing car for winter very easy as I plan on removing tires and storing in basement for our cold
Minnesota winter.

Agree! These are a great investment and easy to install. A win, win mod for all

 

[jefc73]

Just ordered the jacking rails.

 

[David@Steeda]

Just ordered the jacking rails.

Awesome! I'll make sure they ship out asap!

 

[BlackMustang690]

I got mine on Saturday, Along with a lot of other parts from Steeda Thanks to David. I will be busy this weekend.

 

[David@Steeda]

Installed my steeda jacking rail today,raised car so all 4 wheels where off ground,put
Jack stands under rail,car was very sturdy,these will make raising car maintance and storing car for winter very easy as I plan on removing tires and storing in basement for our cold
Minnesota winter.

Glad you like the jacking rails!

Sponsored