Zenclosures sub boxes

[shahram72]

I had pics but can't find them now. I ran power wires thru the grommet in the passenger side. IT was hard cause I didn't want to cut too much and risk damaging the harness in there. If u do that, I don't even want to imagine the nightmare cost of fixing that issue. Be careful. Network cabling everywhere in this car.

Sponsored

 

[FirstGT]

Agreed, and they will do a certain amount of customization as well...

anyone know if he can make it fit a single 15?

I dont see dimensions listed on his site, from eyeballing the dual 12s with recessed mount it appears that MAYBE a 15 would fit

 

[mumbles]

anyone know if he can make it fit a single 15?

I dont see dimensions listed on his site, from eyeballing the dual 12s with recessed mount it appears that MAYBE a 15 would fit

Their dual 12 enclosure measures just shy of 15" tall, but they may be able to come up with something...

 

[shahram72]

2- 12's is greater than a 15" Why do u want a 15" ?

 

[FirstGT]

Their dual 12 enclosure measures just shy of 15" tall, but they may be able to come up with something...

ok thanks. I'll have to reach out to him. I didnt see measurements on his site

I was kinda basing it off judging the cutouts for the 12's

I'm not sure my sub will fit anyway due to depth

2- 12's is greater than a 15" Why do u want a 15" ?

yeah I realize that but I have a 15" IdMax laying in my garage that i've been trying to sell unsuccessfully.
If the 15 wont work then i'll probably just do a single 12

 

[jordystang69]

Charcoal grey is the correct carpet match right, not black?

I'm still debating whether I want to run a dual 10 setup, or the single 10 with amp mounting space on other side. Either way I need this asap... base audio is so weak.

 

[mumbles]

Charcoal grey is the correct carpet match right, not black?

I'm still debating whether I want to run a dual 10 setup, or the single 10 with amp mounting space on other side. Either way I need this asap... base audio is so weak.

Correct on the color...

 

[Shagen]

I am glad I found this thread. I ordered the single sub with amp rack and it fits great. Amp is 5 channel Rockford Fosgate P1000X5 if you want to look up rough dimentions on the amp rack.

 

[socal2fast]

I think I'm going with open of these boxes. I'm thinking two 10 inch subs. I'm just trying to figure out front facing or rear facing for the best sound. If I do them rear facing or is there enough space on the back of the box between the seat to mount the amplifiers?

Do the front facing and rear facing boxes take the same amount of trunk space?

 

[scott_0]

if I do them rear facing or is there enough space on the back of the box between the seat to mount the amplifiers?

Do the front facing and rear facing boxes take the same amount of trunk space?

there is not, the box comes right up against the seat backs

 

[Nagare]

Is there space on the sides of the box to fit amps instead then? Not sure if it is a full box or if the box is in the middle and some extra wood is there to fill in the rest to have the nice fit.

 

[scott_0]

Is there space on the sides of the box to fit amps instead then? Not sure if it is a full box or if the box is in the middle and some extra wood is there to fill in the rest to have the nice fit.

yes there is room on the inside to mount an amp(s) but making adjustments would be tricky imo

 

[mumbles]

I think I'm going with open of these boxes. I'm thinking two 10 inch subs. I'm just trying to figure out front facing or rear facing for the best sound. If I do them rear facing or is there enough space on the back of the box between the seat to mount the amplifiers?

Do the front facing and rear facing boxes take the same amount of trunk space?

Go with rear facing for the best results...

 

[cjldad]

Hello everyone.. First time poster, so why not bump up a month old thread..
Looking to add a sub to my 400a Mustang.. Thinking about the single zenclosure with the rack mount.. Anyone running a Rockford P3 12 in theirs? Wondering how well it integrated with the sound and if it was overbearing.. Thanks!

 

[z06psi]

My plan is to put a Rockford Fosgate P3SD2-10 shallow mount into the current Shaker enclosure on the passenger side and then fiberglass a new enclosure on the driver's side for the other RF P3SD2-10.

JL Audio 1000/1V2 to power them.

Wish someone would make a fiberglass driver's side enclosure for us.

Sponsored