Spoilers

[Hoofer]

Very nice thanks for all the help!

Often wished an aftermarket company would design/manufacture a rear spoiler similar to those installed on the '03-'04 Terminators. Just not quite as rounded. It would require it to have a third brake light, or move the current light into it. But at this stage of the game, I'm sure it'll never happen.

Sponsored

 

[Lucabrazi]

All the research I've seen points to this company (assuming they have the style spoiler you want). I don't think you can go wrong with them.

Fyi I did contact them about not drilling and though they can't fully support it, they said to make sure you get adhesion promoter and 3m tape to keep it as solid as possible. The install kit is like $7 on ebay. I can link it if you need it. It's from iKon, I believe.

Hi, can you please provide the link? I could not find the install kit on Ebay. Thanks again!

 

[dman918]

Hi, can you please provide the link? I could not find the install kit on Ebay. Thanks again!

Sure it's here:

https://www.ebay.com/itm/3917067769...8mYvBuiTwC&var=&widget_ver=artemis&media=COPY

 

[Lucabrazi]

Sure it's here:

https://www.ebay.com/itm/3917067769...8mYvBuiTwC&var=&widget_ver=artemis&media=COPY

Thanks, they were sold out but found something similar here by searching the description.

 

[dman918]

Thanks, they were sold out but found something similar here by searching the description.

No problem. They're all pretty much the same so you should be all set!

 

[Lucabrazi]

Hi I received my spoiler from BMC customs:

https://www.bmcextremecustoms.net/mustang-convertible-350r--spoiler-track-pack-style-2015-2017.html

I tried to install it on the car, tape only but the spoiler did not follow the contour of the car. I took it to the dealer and they had the same problem one side would always stick up. The spoiler is perfectly straight. I did not want them to drill into a new car. Has anyone else had this issue with the BMC spoiler?

 

[LethalSteveG]

Here is the LP Carbon GT500 style spoiler on mine and it was very sleek looking. Doesn't stick up that high and I thought it looks awesome.

Here is a link for it. https://www.lethalperformance.com/l...r-spoiler-gt500-style-2015-s550-mustangs.html

 

[Lucabrazi]

Looks great but I have a convertible.

 

[Hoofer]

Hi I received my spoiler from BMC customs:

https://www.bmcextremecustoms.net/mustang-convertible-350r--spoiler-track-pack-style-2015-2017.html

I tried to install it on the car, tape only but the spoiler did not follow the contour of the car. I took it to the dealer and they had the same problem one side would always stick up. The spoiler is perfectly straight. I did not want them to drill into a new car. Has anyone else had this issue with the BMC spoiler?

Ugh. I'm really sorry to hear this. I don't want a bolt on spoiler either.
It's a shame no one makes a nice, simple, spoiler for verts.

 

[Snakebyte]

Hi I received my spoiler from BMC customs:

https://www.bmcextremecustoms.net/mustang-convertible-350r--spoiler-track-pack-style-2015-2017.html

I tried to install it on the car, tape only but the spoiler did not follow the contour of the car. I took it to the dealer and they had the same problem one side would always stick up. The spoiler is perfectly straight. I did not want them to drill into a new car. Has anyone else had this issue with the BMC spoiler?

I too have a convertible and finally found a pre-painted one on eBay especially designed for the convertible. (The curvature of the decklid for the vert and the fastback are different, thus a less than optimum fit if you try to use the FB spoiler.)

It has been three years since I purchased mine so I'll have to look to see if I have record of the supplier and part information. I'll share it if I find it.

I'm extremely pleased with mine. I got it pre-painted which had a clearcoat applied as well. I did bolt it down. The holes in the small blade "spoiler" if you call it that, were located differently than the aftermarket. It did fit well, and maybe I could have gotten away with using a high-end 3M tape. But I'm a bit conservative and wanted a very tight fit between the new spoiler and the deck lid.

 

[Snakebyte]

I too have a convertible and finally found a pre-painted one on eBay especially designed for the convertible. (The curvature of the decklid for the vert and the fastback are different, thus a less than optimum fit if you try to use the FB spoiler.)

It has been three years since I purchased mine so I'll have to look to see if I have record of the supplier and part information. I'll share it if I find it.

I'm extremely pleased with mine. I got it pre-painted which had a clearcoat applied as well. I did bolt it down. The holes in the small blade "spoiler" if you call it that, were located differently than the aftermarket. It did fit well, and maybe I could have gotten away with using a high-end 3M tape. But I'm a bit conservative and wanted a very tight fit between the new spoiler and the deck lid.

eBay's info rolled off into never-never land, but I was able to find my receipt....

 

[Lucabrazi]

Thanks, Wing Tech makes the BMC Custom spoilers. Maybe I just got a bad spoiler. I will post some pictures.

 

[Lucabrazi]

Has anyone put this spoiler from BCM customs on your convertible?

https://www.bmcextremecustoms.net/2...k-spoiler-satin-black-air-design-fo22a17.html

Spoke to BCM customs this morning and they said this spoiler is made out of plastic and the manufacturer used to make parts for Ford. They said this is tape-on only and should be a better fit than the one I purchased.

 

[dman918]

Has anyone put this spoiler from BCM customs on your convertible?

https://www.bmcextremecustoms.net/2...k-spoiler-satin-black-air-design-fo22a17.html

Spoke to BCM customs this morning and they said this spoiler is made out of plastic and the manufacturer used to make parts for Ford. They said this is tape-on only and should be a better fit than the one I purchased.

I looked at this one but not sure if I like the satin black. May swap mine out for one of these track pack spoilers. Current spoiler below. I cut the bolts off and just have it taped on (so I still don't have any holes).

 

[SEAICE]

I've posted pics elsewhere, but thought if someone with a convertible was looking for spoiler examples, I'd post it here for convenience. This is a Shelby GT500 Spoiler I bought from Shelby American, as used on their GT500 Super Snake Convertible. Yes, it did involve drilling new holes... They don't match the stock spoiler holes, but the old holes are covered by the spoiler:

Sponsored