Hp tuners MPVI2 Help.

[MyStang]

Device will not connect to car. Here's the things I have tried:
Resynced MPVI2 on laptop.
Cleared all Bluetooth settings on android phone.
Deleted TDN app and reinstalled.
I get the green light for power, press the Bluetooth button and it flashes fast but no RTD found.
It's driving me crazy. I'm working with Wengerd Performance. I have had several communications with them on tunes, updates, data logs etc... I went to change to the 93 tune and now nothing. Any help would be greatly appreciated.

Sponsored

 

[I Bleed Ford Blue]

Have you tried updating the firmware in the MVIP2 itself?

 

[S550HPP]

I have RTD one and on Samsung tablet would not connect no matter what I tried.

Changed device to LG Velvet and worked flawlessly.

Try a different android device...

 

[MyStang]

I did update to the new HP Tuners software suite. I will have to check for a driver update. And a factory reset to the phone. MVI2 worked fine last week.

 

[ZXMustang]

Make sure the BT speed in the app is set to full not experimental.

 

[MyStang]

Make sure the BT speed in the app is set to full not experimental.

In the TDN App right?

 

[ZXMustang]

In the TDN App right?

Yes

 

[MyStang]

Total reset again. Could I have "BRICKED" my PCM?

 

[ZXMustang]

Total reset again. Could I have "BRICKED" my PCM?

What you can do is plug it in to a computer so the RTD powers on. Then try to connect to it and do a firmware update on it. Your PCM on the car is fine. Its just a connection issue on the RTD.

 

[MyStang]

Update,
HP Tuners has requested that I return this MPVI2 in house for further testing....
I will update when I receive more Information.

 

[5doorsoffury]

when you go on a pc and access your account does it show the rtd as a registered device with the credits still there? i swapped rtd to mpvi3 and this happened. i unregistered in the account and re-registered it with the tdn app and my account then it started to work again.

 

[schmeky]

My old MPVI2+ was not working properly for months. It took me a while to figure this out (using mine to program my 10R80).

Sent a datlog to HPT and they said all is good. I broke out my trusty old Ngauge and converted a file to enc and "BAM" all my changes I had made worked.

Send back my MPVi2+ and traded it in and paid for the MPV13 and all my program changes are now working. I say get the newer "3" version based on my experience.

I personally think HPT may do this on purpose, just like they recently stopped supporting the Ngauge.

 

[ZXMustang]

My old MPVI2+ was not working properly for months. It took me a while to figure this out (using mine to program my 10R80).

Sent a datlog to HPT and they said all is good. I broke out my trusty old Ngauge and converted a file to enc and "BAM" all my changes I had made worked.

Send back my MPVi2+ and traded it in and paid for the MPV13 and all my program changes are now working. I say get the newer "3" version based on my experience.

I personally think HPT may do this on purpose, just like they recently stopped supporting the Ngauge.

I tune exclusively with an MPVI2+ and it’s been rock steady for about 4 years. No need to upgrade yet.

 

[I Bleed Ford Blue]

Yep, bought mine back in 18 and it still works. I have both my mach 1 and my explorer ST both tuned right now, and I just down graded the explorer last week because the wife is driving it.

 

[MyStang]

I picked mine up in 2019. It was working great until I wanted to swap to a different tune.
It has lost its Bluetooth ability.
I have always taken good care of it.

Sponsored