19x10 +48mm offset with spacer?

[Remy_reign]

Hey ive been looking around this forum for a while trying to get the answer
this question, please help!!

Im looking to buy the 19x10's pp wheels from american muscle for the front.
i realize they wont fit. but with a spacer would they? and if so which size of a spacer would i need?

Thank you

Sponsored

 

[Need4SpeedMotors]

You will nneed a 5 mm spacer, the factory 19x9.5 GT PP wheels have been put upfront before. It works and looks good.

 

[Remy_reign]

nice so to get these 19x10's i just need a spacer.

http://www.americanmuscle.com/performance-pack-black-19x10-2015.html

i planned on going 1 inch with the spacer so i should be good right?

 

[Need4SpeedMotors]

Apologies

So the 19x10 they have works, its tucked in a tad so you can space it out if you desire

I worded my first post incorrectly lol my bad.

 

[Remy_reign]

Apologies

So the 19x10 they have works, its tucked in a tad so you can space it out if you desire

I worded my first post incorrectly lol my bad.

No worries! and awesome thanks!

 

[Quiksilver15]

1" spacer with a 19*10? That's going to poke like crazy

 

[Masorcas]

So would the stock 19x9.5 from the rear poke upfront with a 1" spacer?? I plan on putting the rear pp 19x9.5 upfront with a 275/35r19 with the 1" spacer and the AM replica 19x10 in the rear with a 305/35r19 maybe put the spacer will see when they get here

 

[Need4SpeedMotors]

So would the stock 19x9.5 from the rear poke upfront with a 1" spacer?? I plan on putting the rear pp 19x9.5 upfront with a 275/35r19 with the 1" spacer and the AM replica 19x10 in the rear with a 305/35r19 maybe put the spacer will see when they get here

the rear can work, you just need a 5 mm spacer thats all

As for the 19x10 rear i would not advise a 1" adapter, the offset will be too low IMO id much rather say pop a 5 mm on as well.

 

[Quiksilver15]

I agree, I would just run a 5mm spacer at both ends. 1" adaptor will poke quite a bit with both 9.5" and 10" wheels.

Side note I will be running a set of 19*10 American Muscle Boss 302S wheels (+47.5mm) on my GT soon, ordered 5mm spacers for all around the car. I will be running a square set up.

 

[Need4SpeedMotors]

I agree, I would just run a 5mm spacer at both ends. 1" adaptor will poke quite a bit with both 9.5" and 10" wheels.

Side note I will be running a set of 19*10 American Muscle Boss 302S wheels (+47.5mm) on my GT soon, ordered 5mm spacers for all around the car. I will be running a square set up.

itll be a good setup.

 

[Remy_reign]

i would like to see it, i have been looking at square setups with spacers and so far they dont look bad. i thought 1' would give the same poke all the way around.

 

[Remy_reign]

like im not sure what the tire width is for the ecopp but this stance is what i desire

 

[Need4SpeedMotors]

Thats HTX's setup if not mistaken so thats the factory with a spacer

Were changing his setup to the GF9 19x9.5 ET 30 square setup now.

Sponsored